Fabric consumption on a bathrobe. Male bathrobe with their own hands with a nominal embroidery - the best gift to a man

25.08.2019

Look at what a cute robe we will simulate today! In the wardrobe of any woman, such a robe is simply obliged to be! Even if you wear it, you will not often) And to sew it - very simple.

In the photo - a galaxy of silk, but you can use any fabric you like. High quality galact, yes, from natural silk, a thing is not cheaper, as well, that we can sehe yourself such a wonderful thing! When you choose a cloth, pay attention also to all kinds of artificial silk, chiffons, atlas and cream satin, as well as on lace canvases, because they also fit perfectly in our case. For decoration you will need either a silk decorative tape, or a lace tape - about two and a half of the robe.

Here, look at how the same bathrobe can look, but made of another fabric, and decorated with another finish:

To proceed with the modeling of the coat, we need to take your basic dress pattern. If you still do not have a basic pattern, then you can print it on our site, as it costs it quite inexpensive, and the products stitched through it will sit on you perfect! It will only be necessary to enter the values \u200b\u200bof the measure that you can remove yourself, and output the resulting pattern to the usual home printer:

First step. So, let's start modeling! You have already printed your base pattern (the truth is how to create a pattern - Ishoy with our service is very simple !?), and now we will bring it to the desired result. First of all, we need to get rid of breastplate on the shelf, and from the scuba diversion on the back. Make it very simple - you need to translate the ladder into the armor. First we translate the chest extract - measure its solution and retreat exactly the same distance from the leftmost shoulder point. We connect the resulting point with the upper edge of the neck, draw a new line of the armor (so that it is as similar to the old one.) In Figure 1, the red dotted line shows how to do it. We also do the same with the scooping sweeping - we measure its solution, departing from the edge of the shoulder the same value, and draw a new line of the armhole. We forget about old swallows (in Figure 1 it can be seen that they are crossed out.)

The second step. Take a small one-piece sleeves to our shelf and the back. You can, if you want, draw and sleeves cutting a "bat". Figure 2 is drawn how to do it. We disassembled both types of these sleeves in the topics article:

Third step. Now let's bring to mind the back of our coat. As can be seen from the sketch, the bathrobe has an overlooking view, as well as the rounded bottom of the back. In order to achieve such an effect, we also expand our robe from the waist line to the bottom line at a distance equal to 5 to 10 cm. In Figure 3, blue arrows and red lines show how to do it. And also bending the bottom line down by 5-7 cm.

Fourth step. The back is ready, now make a shelf detail. To begin with, we draw a symmetric reflection of the shelf relative to the axis of the symmetry, which is shown in Figure 4 of the blue dotted line. Now we are expanding the robe from the waist line to the bottom line to the distance from 5 to 10 cm (this distance should coincide with the value of the backrest expansion in the last step.) In our case, we expand the balacy of 5 cm, and how we expand it shown by the blue arrow and Line of red in Figure 4. Well, in conclusion, we need to line the board of the bathrobe just as it is depicted in the photo and on the sketch - namely, the angle: we start to conduct a smooth rounded line from the beginning of the neck, draw a V-shaped neck, and In the same spirit, we continue to the line of board to the Niza himself.

Fifth step. So, see, please, how the shelf item should look like a finished form:

Tip: Shoulder seams Shelves should be equal to the shoulder seams of the back! And the side seams shelves must be equal to the side seams of the back! Carefully check all the lengths before starting to cut to avoid difficulties and inconsistencies

And now look at another cute robe from the new collection from Cavalli and inspire !!!:

What can be more pleasant for a man than coming home after a long working day, change clothes into a soft cozy homemade clothing. Most men prefer to wear a T-shirt and sports pants in the home atmosphere, possibly due to the lack of an alternative. But today everything will change, because we present you a royal luxurious home bathrobe, which you can sew your husband, father or son yourself. They deserved it with their attitude towards you, their concern and love. So let's and we will reply to them reciprocating and give this wonderful bathrobe, in the sewing of which the particle of your soul will be invested.

This bathrobe sews from a soft velor on cotton basis, but you can use for sewing this model any suitable cloth with a short pile - velor, velveteen, velvet, etc.

And now very good news that will please you! You can build a dressing of a bathrobe on our instructions or download the finished pattern of a robe on 52-56 sizes completely free!

The pattern of a robe is given per dimensions of 52-56. Model length 132 cm.

Building start from the grid Pattern: Build a rectangle AVD: AB \u003d 72 cm, AC \u003d 132 cm.

Building a rod shelf pattern

The width of the shelf is \u003d 40 cm. From the point n, set off to the left PP1 \u003d 3.5 cm, deposit from the point of P1. 3 cm. Spend from the point 3 of the shoulder line of the shelf with a length of 20 cm in such a way that the P3 points lay on the AP lines. From the extreme point of the shoulder, put down 29 cm and build a shelf rural line.

Building a challery collar

From point P3, set aside to the left 14 cm. From point P3, spend up a length of 9.5 cm. At a right angle, swipe a length of 12 cm. Spend the outer side of the challery collar slightly rounded. From the point to the right, deposit 8 cm and swipe the seabed line (dotted line).

Draw a pocket pattern of 17.5 x 18.5 cm, the lower corners of the pocket turn. State your pocket position on the shelf as shown in Fig. one.

Building the backing pattern

From the point in set down to the left of the BB1 \u200b\u200b\u003d 8.5 cm. From point n Put down to the right PP2 \u003d 3.5 cm and down 3 cm. Spend the shoulder line of the backrest 20 cm long and the backrest line is similar to the shelf.

Bill-boulders are located along the side of the side at a distance of 10 cm from the lower point of the armor. The length of the bonding 14 cm - 2 clamps of 7.5 cm (depending on the level of the waistline, you can make a belt to the upper or lower lip). The back is lifted with a fold in the center. The weld to move onto the tracing and carve out separately.

IMPORTANT! Side seams can not be done if the width of the tissue allows. Spread out the pattern on the fabric, without cutting through the side of the side, as shown in Fig. one.

Stop shoulder seams, in the corners of the allowance. Still the middle seam on the postponed collar-sock. Put the collar in the neck of the back. Stop the weld of the middle seam of the collar. On the weld, run the finishing braid on the markup. Cut the chain to the shelves along the outer edge, cut the batteries. Introduction to the bottom of a bathrobe and sysert. Picks Beg the front side and clean the edge of the edge on the edge of the edge, to the center of the back of the head of the hinge (so that the robe is comfortable to hang on the hook), the fee will shoot.

Still seams of sleeves. Put the sleeves in the armor. Sleeveless battles are adjusted and syrete.

Pads at the top of the pockets are adjusted and syrete. On the details of the pockets on the markup, insert the finishing braid. Pads on the side and lower sides of the pockets are adjusted and pockets on the stitching on the shelves.

Call 2 strips for a 3 cm wide and 17 cm long. 1 cm wide loop width, sewing and pinching bumps on the side seams on the markup. See more. Stretch the bump exactly in the center of the short line.

Bathrobe ready! It remains only to give it to your man and enjoy him delighted, thanks and kisses!

We offer you to download the finished pattern of a robe 52-56 sizes. Download the pattern in full format and print it at the Copy Center (A0 format).

Download the pattern, print it on sheets of A4 sheets and glue the sheets by alignment. To check the print format, use the test square (the size of the test square 100 x 100 mm).

Fig. Pattern of a male robe for download

Recalling a detail of the fee and part of the pocket separately. Extend the shelves and backs of 40 cm.

Fig. 3. Details of the pattern of male robe in the finished form

If you allow the width of the fabric, the shelf and leave the back without side seam. The instructions on the creation and tailoring of the male robe see above.

Home clothing must be comfortable and free, but at the same time I want it to look no less attractive than the weekend. This is especially true of the most common option for the house: Kolata. If it is not possible to find an attractive model in the store, you can sew it yourself - for example, a robe with a smell: elegant, but spacious, and even though it is absolutely not fitted, well emphasizing the figure. How to sew a robe with smell?

The classic robe with the smell can be performed without side seams - sufficiently upper, between the shelves and the back. In addition, it often lacks even sleeves and buttons that replaces the belt. However, you can simply make a secret clasp so that the product does not lose its ease. For such a bathrobe, it is recommended to take subtle and not too smooth fabrics: cotton, sitherium, batter.

The pattern for a robe with the smell can be built even without performing complex calculations: the silhouette is free, as a result of which the roles are not played in 2-3 cm. In addition, it does not have latches, which also simplifies the sewing process.
The basis of such a bathrobe is a rectangle. The total width (Mn segment multiplied by 2) is equal to the girth of the thighs with the addition of 5-8 cm. NP segment, marking the smell, is set to 15 cm wide, and relevant for the left and right shelves.
The length of the product is selected arbitrarily, so this value on the pattern is not specified. The height of the sides (from the waist to the lower point of the sleeve) is 17-20 cm, depending on how free the sleeve should be. The same applies to the depth of the neck.

There is no special problem in combining the details of the special problem: first, process the sleeves with a zigzag or overlock, then cut down the rope and the back, then also treat the neck and edges of the product. If you need to make a secret clasp, it is recommended to put it at the intersection of the waist line and vertical from point N.

The finished bathrobe can be supplemented with an oblique baker, brushed along the edge of the shelves and the neck. The bottom of it is not recommended to process. For monochrome bathrobes, the fabank is cut out of the same material, for fabrics with a pattern take a satin or satin tape so that it does not argue with the main pattern.
If you want to make the sleeves to such a coat, consult their classic pattern, but do not apply to the wrist: the main idea of \u200b\u200bbathrobes with a smell is lightness and freedom that can be traced in every detail.

This option of homewear also belongs to the products with a smell, however, has some features: in particular, Kamono Kimono is sewn not fit - it is always loose clothes, if you contact traditional oriental clothes, and also assumes the presence of a wide soda sleeve. In addition, such a bathrobe has a belt, which can be both a standard width (2-3 cm), and closer to Japanese Ob - 10-15 cm.

The pattern of a kamono robe consists of 6 details: a single back, left and right shelves, as well as sleeves and 2 belt parts. Even a beginner master will cope with the construction. Recommended material for such a product - silk, as required by traditional rules. But you can replace it with a different light fabric.

All details are built from classic rectangles, so it is quite difficult to make a mistake. The length of the belt is chosen arbitrarily, depending on how it should be tieved. The formula from + 40 (45) see is most often used.

The length of the classic Kolata-Kimono - until the middle of the leg: it is with this calculation that the silhouette will look elegant and attractive. The backrest width is calculated as the "back width", multiplied by 1.2-1.5. In this case, the front half and the rear equal in the width of each other.
SCOS on the shelves, coming from the neck, ends on the waist line, and the lower points of the side cuts for the sleeves should be approximately 15 cm above.

Details are stitched together as follows: First, the shelves of the top seam are applied to the back, and the fabric left on the allowance is rooted back. Then sleeves are added, and the shelves are connected to the back of the side seams. It remains only to sew belt details so that it is dense and empty inside, and Kimono is ready to settle in the wardrobe.

Dress-gown dress from cotton padded fabric for women with a full figure. Unsurrence through the waist, from under the coquette, single-circuit with sleeves, are formed soft assemblies. Details - a pointed collar. Large, overhead pockets with valves, booster bar - SECd.
Recommended dimensions: 44-56.
Fabric consumption: size 48, height III - 4 and with a width of 80 cm.
Author V. Turovseva

A robe made of lightly stinging silk fabric. Cutting along the waist, shelves on the coquettes, from under which soft builds are formed with a deep odor and a fastener on one button. Sleeves - "Wings" are pressed in Ocape. Coquette is counted.
Recommended dimensions: 44-50.
Fabric consumption: size 48, height of III - Z0 cm with a width of 90 cm.
Author N. Baskakova

Summer cotton robe for a woman with a full figure. Unchanging on the waist, shelves with attraction sides. Cutout neck, board, bottom products and curly false pockets are decorated with a roll or braid. Recommended dimensions: 52-56

fabric consumption: size 54, growth IV - 3 m 20 cm with a width of 90 cm.

Summer, beach bathrobe for a full woman. One-piece, straight silhouette, a bodice in front with small coquettes, from which soft assemblies are formed. V - neckline neckline, prugis, large overhead pockets, board and bottom products finished by a roll or edge
Recommended dimensions 52-56.
Fabric consumption: size 54, growth IV - 4 m 20 cm with a width of 78 cm.
Author F. Schukayev

Cozy cotton padded fabric bathrobe for middle-aged women. The large challenge collar, the edge of the side and the bottom of a half-legged, highly extended sleeves are edged. Narrow gently tied belt. Author K. Mitskevich.
Drawing 54 size, growth

Hello, needlewomen. Excessive bathrobe will not hurt us? See how to sew a bathrobe without pattern.

Simple model home coat with smell

The bathrobe is a very convenient thing, and when you safer her with your own hands, it can become a real work of art. For home, you can come up with such jewelry in which you will not go to people. But at home, too, you have to be beautiful, well-groomed.

First, without pattern, a savory bathrobe with a smell. If you know how to keep a needle in your hand, then this is not a problem for you. Let your home clothing remain shorts with a t-shirt, but there will be no domestic barbecue.

Why should I sew a little thing with the smell? It is convenient for the fact that you can quickly tie, without getting rolling with lightning and buttons, and buttons can break away, the loops come into disrepair, and the hlystics or the belt never!

How much material will need

For this design, the wardrobe can be taken any material, but the dimensions must be such: with a width of 150 cm take a length equal to the length of the product if your size is up to 54th, and if more, then 2 times more.

Calculate the width by the formula: Plus 20 cm. Crees - it is a semi-breaking hips.

Building patterns we make immediately on the fabric.

First, the fabric is well set up the iron.
Spread on the table.
Fabric 150 cm wide fold in half off inside, narrow tissue, 80 cm wide - across.
Small applied points of the future pattern.
On narrow tissue from the left edge, 1.5 cm for seam on the back is departed.
Build the pattern from above.
From above, we make an indent for the line - 1 cm.
From this retirement to the right we conduct a straight line
On this line from the bend, the backrest to the edge measured 9 cm, and from the left corner, I dwell down 2 cm, we put the point. Connect two points. It will be a neck from the side of the back.
Further to the right of the bend, reflect + 20 cm. At this mark, the straight line is on top.
On it there is a neckline on the front shelf: you need to measure the distance from the shoulder to the waist, postpone this value on a straight line.
On the top of the draw, laid horizontally, left 9 cm from the edge, put the point.
Connect 2 labels.
The upper horizontal line should be divided by half.
Down from this point is a straight line for 26 cm.
It makes an incision for hands.
Next, cut out the details.

Sewing products

Zigzag process the edges of the details.
We sew the back with narrow matter.
Before and the back is folded to face, we combine on the shoulders.
We bring the sleeves and bottom.
Sew belt, 4 cm wide.
Finishing baking process the neck and edge of the transfer.

You can also sew bathrobe of terry fabric.

How to sew a robe without sleeves and without side seams

Let's fuel without sleeves, and even without side seams. We will make the upper seams between the back and shelves. And the sleeves, buttons will replace the belt or counted clasp, so it sews very quickly.

) FUNCTION RUNERROR () (

The base of the coat is a simple rectangle. The width is (Mn multiplied by 2) equals the girth of the hips plus 8-10 cm. The NP segment is given on the smell, equal to 15 cm on both shelves. The length of the product is any.

The height of the barrel (from the waist to the lower label of the sleeve) is equal to 17-20 cm. This size choose as you like. Choose the depth of the neck alone.

Start sewing:

We treat zigzag opening sleeves.
On top of stitching shelves and back,
We treat the neck, as well as the edges of the product.
If you decide to make a secret clasp, put it at the intersection of the waist line and vertical from point N.
Shelves and neck treat with finished finishing material.
NEW.

Like Japanese beauties

Let's firm kalat -komono.

Kamono Kimono is sewn free with wide soda sleeves, without fail, the width is closer to Japanese Obi equals 10-15 cm. The pattern is very simple, consisting of 6 details:

Open back.
Left and right shelves.
Rectangular sleeves.
Two belt details.

It is better to sew from silk, then you will be like a real Eastern beauty.

Sewing order, as above text, just need to sew the sleeves. Sew a rectangle, then sew to the armor.