Beauty and health of teeth 

The density of insulation for clothes. Insulation for winter clothes. Advantages and disadvantages of natural insulation

The approach of winter makes you think about your wardrobe, encourages you to check whether everything is ready for the season, whether there is the necessary outerwear. If it turns out that the old thing has already worn out enough and gone out of fashion, you will have to purchase a new one. For example, a winter coat. How to choose it correctly? What should be paid special attention to?

Everyone knows that the fabric itself does not heat up much, and in order for the coat to become more or less warm, you need to sew a heater into it. This is the most important part of winter clothing, despite the fact that no one sees it.

Insulation performs the main task - heats the body. More recently, no one could be frightened by the choice of insulation for the winter, but now a lot of foreign words have appeared on the labels that plunge the buyer into indecision and make it difficult to buy the right thing.

What types of insulation for winter clothes does the textile industry offer? Consider the advantages and disadvantages of each of them in more detail.

Insulation for clothes: types and characteristics

There are two types of heaters - organic, that is, natural and synthetic.

Natural heaters

fluff, which belongs to natural heaters, is the most popular, since its lightness and thermal insulation remain at a high level.

It is lightweight and retains heat at low temperatures, in addition, high-quality fluff lasts a very long time. In any downy clothing, the composition of the insulation contains a feather. This is necessary for the uniform distribution of fluff throughout the product.

Disadvantages: down insulation can cause allergies and therefore must undergo mandatory antibacterial treatment (which some companies neglect); the complexity of care (washing, drying) at home.

Batting- a half-woolen insulation, which in the middle to the end of the last century was used in the Soviet clothing industry when sewing overalls, and also as a heater for winter coats.


Currently, batting is less and less popular.
Disadvantages: high weight and relatively high water-retaining properties. Wool and fur very often used as a lining for winter clothes - a wonderful natural material, known for its high warming properties, as well as ease of care for it.


New Zealand Merino wool is rightfully considered one of the highest quality materials for the production of excellent wool insulation for children's winter clothes.

Disadvantages: high hygroscopicity and still considerable weight.

Synthetic insulation

Sintepon- is one of the most common synthetic insulation. It is made from polyester fibers bonded with adhesive, needle-punched or thermal methods. Light, warm, voluminous, cheap - at one time such a heater was at the peak of popularity.


However, as time has shown, the synthetic winterizer has a number of disadvantages: increased moisture permeability, air tightness, rapid deformation and fragility of the material - all this has led to the fact that the synthetic winterizer is used as a heater for the production of cheaper demi-season and winter clothes.

Hollofiber Hollow fiber (hollow fiber)- a non-woven fabric filled with synthetic fibers in the form of spirals, balls, springs, etc. It is this structure that makes the thing warm, since a lot of air is stored between the fibers.


By right it is considered a heater of the 21st century. Light, warm, moisture and shape resistant, hypoallergenic - it is an excellent material for the production of excellent insulation for winter clothes.

Varieties - polyfiber, thermofiber, fiberskin, fibertek, etc.

Thinsulate (Thinsulate) is one of the most expensive heaters. It is also called artificial down - it is just as light and warm. But unlike fluff, thinsulate cannot cause allergies and holds volume better without straying.


Fleece- made from polyethylene terephthalate fiber. Not only sweaters, sweatshirts, sweatshirts are sewn from it, but they are also used as a lining for a jacket or coat.


The main characteristic of fleece is the amazing lightness of the material with high warming performance.

Sherstipon (wattelin) refers to a mixed type of heaters. It consists of wool and polyester fibers in different proportions. The production technology of this insulation consists in passing the material through a carding machine, and then through a thermal oven to fix fluffy fibers.


The choice of insulation for a coat depends on the lifestyle and purpose of outerwear, as well as on the area of ​​\u200b\u200bresidence. For warm city winters and office days, a padding lining may be enough. People who are fond of outdoor activities or work outdoors in winter should pick up outerwear on modern synthetic insulation.

Polyester is both a fabric and a man-made fiber, so confusion can arise. In everyday life, polyester is most often called the material for sewing products. In this sense, the difference between it and synthetic winterizer is significant, although one chemical fiber, polyester, is used for production. Polyester, in turn, is made from chemicals found in petroleum. It was invented as an alternative to natural materials.

To know how a synthetic winterizer differs from polyester is necessary in order to navigate well in the world of textile products. Polyester is a common name, and there are many varieties of polyester fabrics depending on their purpose. There are woven materials that are made on looms and are a canvas of interwoven threads. And there are non-woven, where the fibers are interconnected in various ways.

A synthetic winterizer is a non-woven material, which is a light, loose and airy fabric used as a heater in outerwear and a filler for various products. They are stuffed with toys, used for mattress toppers, in the production of upholstered furniture. Polyester fabric for sewing clothes and other textile products differs from synthetic winterizer in the production method, thickness and density, but their composition is the same.

The polyester used for sewing textiles is known for its durability and water repellency. In this regard, it is great for making outerwear. Things do not lose their shape for a long time, they tolerate washing well. They need to be ironed at the minimum or medium temperature of the iron. But ironing may not be required at all, since polyester clothes practically do not wrinkle. Some people may be allergic to natural wool.

The difference between polyester that it does not cause allergic reactions, but may not be very pleasant to the body. It is best not to wear this material in hot weather.

Polyester added to cotton or wool significantly improves the properties of fabrics. They hold their shape better, wrinkle less and do not shrink.

This material is actively used for sewing textile products such as curtains, bedspreads, upholstery fabric for furniture. In this regard, he has no equal. Products look great, they last a long time, do not fade in the sun and do not rub.

Affordable and common filler

Sintepon is a cheap and easy-to-manufacture material. Now there are many types similar to a synthetic winterizer with improved qualities. They have their own patented names - isosoft, holofiber, tinsulate, etc. The synthetic winterizer is not registered as a trademark, so it is produced by different manufacturers. The quality of the material can vary greatly. Therefore, when choosing clothes, you need to pay attention to the company, the quality of tailoring the product. At the same time, the label in the composition may simply indicate 100% polyester. This means that both the upper and the inside of the garment are made of polyester fibers.

Properties of a synthetic winterizer and care for things

In the production of the material, polyester fibers are joined together by a hot-melt or thermal method. This results in a voluminous and light filler. Its main property is thermal insulation ability. Products insulated with padding polyester can be worn up to -10-150 C 0.

Since this is a cheap material, it wears out quite quickly, loses its shape and its thermal insulation properties, the fibers can break through, worsening the appearance of the product.

Things on the padding polyester need to be properly looked after so that they serve longer. Gentle washing is allowed at a temperature of 300 C 0. Do not dry things near heating appliances and iron with high heat of the iron.

Thus, in its composition, synthetic winterizer and polyester are no different., since both are made from the same fibers. But their appearance, properties and purpose are different. The range of manufactured products is very wide - these are light summer clothes, tracksuits, insulated jackets, curtains, carpets, etc. Polyester fabric is used for sewing products, and synthetic winterizer is used for warming winter and demi-season items.

Fillers for children's winter clothes
The warmth (and comfort) of winter clothing is largely determined by its filler. Long gone are the days when parents had only faux fur coats or jackets on a heavy padding polyester to choose from.
Now, in the production of children's clothing, fillers of a new generation are used, and even a modern synthetic winterizer is "no match for its great-grandfather." In clothes with such fillers, the child will not only be warm, but also comfortable on winter walks during his games with friends. After all, thanks to unique developments, their structure allows you to better retain heat, which means that the desired temperature regime can be achieved using a thinner insulation, which makes products made from them lighter and thinner.
Let us consider in more detail the most common types of fillers for children's winter and demi-season clothing.

Sintepon
The synthetic winterizer has been used as a heater for children's clothing for a very long time, but during this time it has also undergone evolution. And although the modern synthetic winterizer, like its progenitor 15 years ago, is also made of polyester fibers bonded together thermally, otherwise they have little in common. A stern synthetic winterizer is dense, and a new one is hollow.
The old one was laid in parallel layers. Because of this, he had very low rates of heat conservation and moisture conductivity. Now such a synthetic winterizer (thick, adhesive) is used only in cheap products. In the new padding polyester, the fibers are not glued, but rather hold each other with silicone needles. Such insulation is more durable, does not lose its shape. And although it is quite light, it still continues to be inferior to modern heaters (isosoft, thinsulate, etc.).

Minuses:
- after exposure to sweat and washing, it loses up to half the thickness, and, as you understand, any children's product has to be washed quite often.
- with a decrease in consumer properties due to operation, the synthetic winterizer becomes not very suitable for a cold winter. With a loss of thickness, the lower limit of the temperature regime is reduced to -10 °. Therefore, it is better to buy overalls based on synthetic winterizer for demi-season.
The main advantages are low price and a large selection: Many modern companies now produce children's winter clothes on synthetic winterizer: domestic factories, as well as companies from China and Poland. Our manufacturers in most cases order tailoring in China.
Care: Wash at 30°C using only mild detergents that do not contain bleach; do not soak or bleach.

In Russia, the name lavsan is still known, which does not create the appearance of using any super technologies, and it is technically not so difficult to produce a fiber with cavities inside. Sometimes the synthetic winterizer is used not for warming, but for filling, so that the clothes do not look too thin and please the eyes of suspicious mothers.
The synthetic winterizer can have a density of 50 to 600 gr. per square meter, can be made using different technologies and be voluminous and not. In clothes, one layer of synthetic winterizer or several can be used. For example, for children's winter jackets, three layers of 100gr/sq.m. are often used, i.е. TOTAL: 300 gr./sq.m

And at what temperature are clothes with different thicknesses of synthetic winterizer designed?
100 gr - this is autumn / spring - from about 0 ... + 5 to + 15 ...;
250 gr is a demi-season - from +10 to -5 approximately.
300-350 - cold winter, up to about -25.

Manufacturers of clothing with synthetic winterizer filler:

O "HARA, Canada. Jackets and sets for spring made of 100% polyester (top and lining fabric).
COCCODRILLO, Poland.
ORBI, Russia.
Freeman, Russia. The Ryazan factory "Golubaya Oka" sews on Italian and German equipment. Fabric: polyester, lining - cotton and polyester.
"OVAS", Russia. Materials - polyester.
LAMO, Russia. Top fabrics: blended with cotton, treated with special Aqua Stop impregnations, for lining - cotton or blended fabrics.
Yoot, St. Petersburg. Shell fabric: Polyester Dewspo, Lining: 190T Nylon Taffeta, Finish: Polar fleece.
V-Baby, Ukraine. Upper and lining fabrics: 100% polyester, trim: fleece.
Donilo. The so-called "factory China". Fabrics: 100% polyester.
KIKO (kikokids). Has a lot in common with Donilo. 100% polyester, lining - cotton, fleece.
Insulation: isosoft

ISOSOFT (Isosoft) - a modern synthetic insulation with a thermally sealed surface, made from fibers in the form of balls. The balls do not communicate with each other and contain cavities, which is why the product on isosoft keeps its shape and heat well. The special microcellular structure does not allow cold air to penetrate inside, keeping warm. Isosoft clothing creates an ideal microclimate around the body, depending on the activity of the child and the weather. Possess high heat-shielding properties.

Soft as fluff, ISOSOFT (Isosoft) is two or more times warmer than conventional synthetic insulation, easily restores its shape after compression and does not lose it after numerous washes. And besides that, they are also very light.

In a product with such a heater, the baby will never freeze, and the slight thickness and extraordinary lightness will allow the child to move freely, which is decisive when compared with the same padding polyester.

The unique surface of the material allows you to combine isosoft insulation with different fabrics, reducing the wear time of the fabric.

Usually, in the description of children's outerwear on isosoft, the weight of the synthetic insulation in the product is indicated, for example: "isosoft 260 g / sq.m." What kind of weather are these indicators calculated for:
* 40-70 g/sq.m. – warm autumn-spring
* 100-150 g/sq.m. – cold autumn-spring, warm winter
* 200-300 g/sq.m. - frosty winter
Isosoft clothes are easy to care for: they are easy to wash in the washing machine and dry quickly., Recommendations for the care of products with ISOSOFT insulation (Isosoft)
- do not soak
- machine wash at 30 - 40 degrees
- Do not use chlorine-containing products.

Advantages of Isosoft insulation when compared with down:
does not cause allergies;
does not require mandatory dry cleaning;
easily erased;
dries quickly;
gives a feeling of comfort both at + 5°C and at - 20°C.

Advantages of Isosoft insulation when compared with synthetic winterizer:
much thinner (replaces 4 layers of synthetic winterizer);
easily restores its shape after storage in a folded form and retains it during long-term operation;
does not lose properties after numerous washes;
has the effect of a thermos (retains body heat).
Children's overalls on isosoft:
Kerry (Finland), Lenne (Finland). Made in the same factory. Fabric: Finalyson action (Active fabric), waterproof, stain resistant. Trousers in the back are stitched with a special tape. Reflectors, nickel-free press studs, detachable hood with fur trim, cuffs for arms and legs;
Gusti (Finland);
Tilson (Norway);
Naughty (Russia). Upper: 100% nylon, lining: polyester and cotton;
Reima (Finland);
Etty-Detti (Russia). Brand of the company "World of Childhood". Upper fabric: 100% polyamide, lining: jersey.
Manufacturers themselves most often simply indicate "100% polyester insulation" on the label.
Thinsulate
The unique ultra-light insulation of the new generation Thinsulate ™ ((from the English. thin - thin, insulation - warming) will protect your child from cold, rain and wind in our harsh Siberian climatic conditions.
Structure and properties
Thinsulate™ consists of microfibers identical to the finest down fibers. The idea of ​​creating such material borders on art. Products insulated with Thinsulate™ provide comfort by trapping air molecules between the fibres. And the more air is in a certain volume, the higher the thermal insulation of the insulation.

So why is the property of Thinsulate™ insulation unique? The more insulation fibers are per unit volume, the more air the material is able to hold. Thinsulate insulation consists of unique microfibers, which are 50 to 70 times thinner than a human hair, their diameter is from 2 to 10 microns. Around each fiber is a layer of air. He will warm your baby, capturing the heat of his body. The thinner the fibers, the more heat-insulating layers in clothing. This makes Thinsulate™ insulation 2 times warmer than the warmest down. At the same time, it breathes well, does not dampen and is easily washed at home without losing its properties.

Thinsulate ™ insulation has become a synthetic substitute for natural fluff, without at the same time having its drawbacks: the ability to absorb moisture from the material is less than 1%. Thinsulate reliably retains heat and allows excess moisture to escape unhindered. This insulation does not restrict movement and provides complete comfort even in the most severe frosts.

Features of Thinsulate™ filler
Warmth without excess volume (light weight and small thickness of the Thinsulate™ filler makes it weightless and relatively bulky);
1.5-2 times warmer than natural fluff;
Higher breathability compared to down and feather products. The main thing in all heaters is the ability to retain air. The more bound air is retained per unit volume of insulation, the better it retains heat. For Thinsulate™ insulation, this value is almost 10 times greater than for other materials;
Greater thermal insulation effect than other polyester fillers of similar thickness and density;
Maintains the necessary moisture balance;
Environmentally friendly and hypoallergenic material;
Resistant to moisture, perfectly erased;
Due to the three-dimensional bonding of the fibers, it retains its unique properties and shape after many washes. Due to the high resistance to squeezing, it does not go astray and does not shrink the product after washing at 40 ° C (about 10% after repeated washings).;
Has the European environmental certificate Oeko-Tex Standard 100.

Care
Machine wash with spin at 40°.
Thinsulate insulation does not lose its properties after washing or dry cleaning, subject to the 3M care recommendations for the corresponding type of insulation. However, a different mode may be provided for the upper or lining fabric. Therefore, pay attention to the recommendations for care from the manufacturer of the entire product.

Clothes on tinsulate are sewn for athletes, oil workers, climbers. Tinusleite clothing (as well as its analogues - Hollofil (Hollofil), Quallowfill (Qualofil), and Polarguard (Polargvard)) is quite expensive. Permissible temperature regime for thinsulate: up to -30 °.
Children's clothes on tinsulate are produced by Ketch (Sweden), TALVI / Talvi (Russia).

Holofiber. The non-woven material of the Hollofiber trademark consists of hollow polyester fibers twisted in the form of springs. The structure of a holofiber is almost similar to the structure of a synthetic winterizer, however, in a synthetic winterizer, the fibers are not hollow, but filled. Due to the hollowness of the fibers, holofiber provides better thermal insulation and less caking. Holofiber provides beautiful shapes, the possibility of long-term operation, is environmentally friendly and non-toxic, does not absorb moisture and odors, and does not support combustion. This is achieved due to the spiral shape of the hair (a type of spiral spring), which allows the product to maintain its shape and easily restore it.

Synthetic heaters (Hollofiber, fiberskin, fibertec, polyfiber) are made from fibers in the form of balls, springs, etc. Balls, spirals or springs do not communicate with each other and contain cavities, so the product keeps its shape well. Clothing with holofiber or fibertec is not very expensive, it turns out the price / quality ratio: for a small price you buy a good overall that can withstand frosts down to -25 °. Thin fibers retain volume, do not absorb moisture, breathe. Manufacturers, most often, indicate in the instructions for the product: "insulation - 100% polyester" (very rarely specify which one: holofiber, fiberskin, fibertec, polyfiber or other).

Isosoft and holofiber: they have almost the same characteristics in terms of heat retention. But based on our personal experience, isosoft is better ...

It happens that manufacturers use a combination of different heaters or a combination of heaters and a membrane, this allows them to register the trade name of a “new” insulation. In terms of its properties, it will still differ little from the known ones. Care: machine wash at 40°.
________________________________________

holofan

It is an interweaving of spiral hollow fibers forming a strong springy structure. This allows the product to retain its shape for a long time and easily restore it. In terms of heat-shielding properties, HOLOFAN is as close as possible to natural down, but unlike down products, it is easy to wash, does not absorb moisture and odors, does not cause allergies, and is also able to retain the heat generated by our body, but not “evaporate” it during prolonged use .

Hollofan - a new generation of insulation!

Light! Keeps warm in cold weather

Does not cause allergies

Removes excess moisture

Maintains and quickly restores its volume during long-term use and repeated washings

Does not absorb odors and moisture

Less often, but still you can find Topsfil - an ultra-light high-tech modern insulation. Provides free air circulation, thanks to it the children's clothes "breathe".
Natural heaters:
Let's not forget to mention also natural heaters, which for many years served faithfully to man in his struggle with adverse natural conditions:
Down, a natural insulation with high thermal insulation properties. Down is the lower layer of bird plumage, which has a structure that retains heat (the down core is thin and short or not at all. Fluffs are spherical in shape). The structure of the down explains the lightness and insulating ability of this natural insulation. The main indicators of fluff: thermal insulation properties, air exchange, softness, weight, elasticity, durability. The main indicators that determine the popularity of down clothing are lightness and high ability to retain heat. The down with the highest of the above indicators is eider down. Eider down is the rarest and most expensive down.
But with all the advantages described, natural down has disadvantages in relation to children's clothing:
- Firstly, children suffering from allergies and respiratory diseases are not recommended to wear down clothes. Down is allergic.
- Secondly, down clothing is best worn in areas with a dry, frosty climate, but in non-frosty, wet winters, downy children's clothing can contribute to the greenhouse effect and the child may overheat.
- Thirdly, children's clothes with fluff are not practical. Children's clothes for children over 3 years of age get dirty very quickly and therefore have to be washed frequently. Down clothing does not like frequent washing, and after washing it dries for a long time.
Care of down products: in order for the product to retain its appearance for a longer time, it is necessary to resort to a complete wash of the product as rarely as possible (it is better to take it to dry cleaning). It is recommended to wash on a gentle cycle (without bleach) at a temperature of about 30°. Machine wash is also possible. After washing, it is necessary to dry and periodically “break lumps” with fluff, otherwise it will fall off. Products with fluff cannot be ironed.
Wool (sheepskin). Sheepskin is widely used in children's outerwear. Sheep wool has anti-stress properties, normalizes blood pressure, helps with diseases of the joints (which is why our grandmothers tied their wrists with woolen thread). High-quality wool is non-allergic, does not contain germs (bacteriological analysis of wool did not reveal any harmful microbes). Sheep wool also contains lanolin. Lanolin has anti-inflammatory (helps the healing of wounds and cracks), anti-edematous and anti-allergic effects. Therefore, sheepskin is not only comfortable, but also extremely useful for children. The most useful, warmest in terms of use in children's clothing is merino wool (Australia). Merino wool is very soft to the touch, perfectly retains heat, has the ability to absorb moisture and at the same time not become wet. This wool is the most comfortable for the child.
Of the minuses, it can be noted that the weight of clothes on sheepskin is quite large, which prevents the child from feeling comfortable and easy during active walks. Therefore, recently, sheepskin has been more used as a lining-waistcoat for winter jackets in the form of a “restored linen”: thick sheep pile on a knitted basis.
Sheepskin Care: Wash on a gentle cycle with a bleach-free detergent at 30°. Machine washable

Pros and cons of holofiber filler.

The cold weather has set in and most people have reached into the closets for down jackets and jackets. For many, winter is associated with large puffy jackets filled with goose down, as well as fur coats. But now a huge amount of clothes filled with holofiber has appeared on the market. In this article we will understand what kind of filler it is and its features.

This is a synthetic non-woven fiber of the polyester group. The structure is very similar to synthetic winterizer, but differs in the absence of the use of glue in production. The holofiber is based on a spiral silicone fiber, which is fastened by soldering at high temperature. The result is long fibers.

There are many positive properties of this material:

  • light weight
  • Excellent thermal conductivity and heat retention capacity
  • low price
  • Hypoallergenic
  • Doesn't absorb odors
  • Not electrified

There are no negative sides to this heater. Unless it is slightly inferior to a goose feather in terms of heat capacity.



Now there is a huge amount of outerwear with holofiber on the market. This is due to the low price. A down jacket costs one and a half times cheaper than a natural one. At the same time, it is not inferior in quality. Before answering about temperature standards, it is worth deciding on the density of the filler. The minimum operating temperature also depends on this figure.

Temperature standards:

  • Density 100 g/sq.m. — from +10°С to +5°С
  • Density 150 g/sq.m. — from +5°С to -10°С
  • Density 200 g/sq.m. — from -10°С to -20°С
  • Density 300 g/sq.m. – from -20°С to -30°С


In principle, the material is made from the same fiber, but using different technologies. The synthetic winterizer is a type of silicone fiber, like holofiber, but all the fibers in it are glued. In holofiber, the threads are interconnected by soldering at high temperature without the use of glue. There is a void inside the fibers, which makes the material light and very warm. Thus, holofiber is much lighter and warmer than synthetic winterizer.



A synthetic winterizer is not the best insulation, as it gets wet and accumulates moisture. At the same time, the material has a low thermal insulation index. It is an order of magnitude higher in holofiber.

Hollofiber competes with natural fluff. Products from it are the warmest. But fluff has one huge drawback - the price. In addition, fluff gets wet in rainy weather. There are also some difficulties when washing down jackets with natural feathers. Given all these indicators, then holofiber is an ideal option.



Women's winter coat, winter jacket, children's overalls, blanket, pillow, mattress: is it better on holofiber or synthetic winterizer?

Sintepon disadvantages:

  • Low thermal insulation ability
  • Accumulates moisture
  • Absorbs odors
  • Quite heavy

Accordingly, holofiber is devoid of these shortcomings. That is why this filler is better. Due to the special siliconization method, holofiber does not accumulate moisture, therefore it is successfully used for the production of blankets and pillows.

If there is a choice between holofiber and synthetic winterizer, when buying a children's overalls, then choose the first option.

Women's winter coat, winter jacket, children's overalls, blanket, pillow, mattress: is it better on holofiber or synthetic winterizer?

Yes, products from this filler can be safely washed in the machine. In this case, it is worth considering the features of the upper fabric. After all, holofiber can be washed even at a temperature of 80 ° C. But due to the fact that down jackets are dyed and made of raincoat fabrics, the optimal washing temperature is 40 ° C. At the same time, the products can be wrung out, because the holofiber is perfectly straightened after washing and wringing. It does not need to be shaken off like fluff.

You can wash not only down jackets, but also blankets, pillows and bedspreads with holofiber. It is these products that can get dirty. Only now there is no need to take them to dry cleaning. You can wash it yourself in the washing machine.



Hollofiber is an excellent filler that will serve as an excellent alternative to natural fluff. It's just as warm, but much cheaper.

VIDEO: Filler holofiber

The women's demi-season raincoat is part of the uniform of the police officers of the new sample. Raincoat of a semi-adjacent silhouette, with a central inner secret fastener for five loops and buttons and additionally for an upper uniform button and a through overcast buttonhole, on a warmed stitched lining. On the coquettes in the area of ​​the shoulder seam, there are two loops and one non-cut loop for attaching removable shoulder straps. Sleeves are set-in, two-sutural. In the lower part of the middle seam of the sleeve there are stitched-in pats, fastened with a loop and a uniform button. Turn-down collar, with detachable stand. The removable belt is threaded into the loops located in the side seams and fastens with a buckle with a tongue, the free end of which is threaded into the loop. On the right collar there is an internal welt pocket with a leaflet. Jacket fabric (100% polyester) with rip-stop weaving threads and water-repellent impregnation. The second layer is the membrane. Filler: Thinsulate 100 g/m. Recommended temperature range: from +10°С to -12°С. Worn with a dark blue scarf or a white scarf. It is allowed to wear a demi-season raincoat neatly folded with the front side out on the left hand. Demi-season raincoats are worn buttoned up. It is allowed to wear demi-season raincoats with the top button undone. Demi-season raincoats are worn with or without removable insulation with a belt fastened with a buckle. Removable shoulder straps in dark blue and stripes in dark blue are worn on this raincoat.

The tunic is part of the daily and exit uniforms of police officers of the new model. Worn with trousers. Material: Suit (semi-woolen) fabric. Composition: 75% wool, 25% polyester 280 g/m2 Lining: Twill 100% viscose 105% g/m2. Fitted, single-breasted, four-button closure. Turn-down collar with lapels. Shelves with cutting barrels. Side pockets are horizontal welt in the "frame" with flaps. A back with the central seam in which lower part the vent is located. Sleeves are set-in, two-sutural. Jacket with lining. On the left shelf of the lining there is an inside pocket with a “leaflet”. Designed for employees of internal affairs bodies with special police ranks, as well as for cadets (listeners) of educational institutions of higher professional education of the Ministry of Internal Affairs of Russia. It has red trim on the sleeves. According to the order of the Ministry of Internal Affairs of Russia No. 575, chevrons are sewn onto the sleeves of the suit at a distance of 8 cm from the edge of the shoulder. A chevron is sewn on the left sleeve, indicating belonging to the Ministry of Internal Affairs of Russia, and on the right sleeve, a chevron, indicating the service of a police officer. You can add chevrons with Velcro. In addition, shoulder straps with buttons are sewn onto this tunic, and two lavalier emblems are also strengthened. How to sew on a shoulder strap? To do this, in addition to the tunic itself and shoulder straps, you will need a ruler, scissors, a needle, a thimble and strong red threads. Be sure to wear a thimble, even if you are used to sewing without it, as sometimes the needle passes through shoulder straps with great difficulty, and you can injure your fingers. If you find it difficult to pull the needle and thread out of the shoulder strap, then you can use pliers or tweezers. 1) First of all, prepare the shoulder strap, i.e. fasten all the required insignia on it, since it will be much more difficult to do this on an already sewn pursuit. 2) Take the shoulder strap and position it so that the side farthest from the button is close to the seam that connects the shoulder of the tunic to the sleeve. At the same time, the upper, directed towards the back, edge of the shoulder strap should go 1 cm from above to the seam running along the shoulder. In other words, the shoulder strap should be slightly shifted forward. 3) Thread the needle into the needle and fasten the shoulder strap to the tunic at three points: at the corners of the shoulder strap, at the place where it comes into contact with the sleeve seam and in the center of the semicircular cut. Now the shoulder strap will be securely fastened and will not move from the correct position during the sewing process. 4) Then we sew the shoulder strap very carefully around the perimeter, making stitches in such a way that only barely visible points remain on its surface in those places where the needle enters the shoulder strap, and the thread between two adjacent holes passes mainly from the wrong side (along the gasket) of the tunic . Then the thread will not be noticeable even if it does not quite match the color of the shoulder straps in color. In this case, the optimal length of each stitch should be about 1 cm. 5) With the second shoulder strap, follow the same pattern. How to strengthen lapel emblems? On the collar of the tunic - along the bisector (the line dividing the corner of the collar in half), at a distance of 25 mm from the corner of the collar to the center of the emblem, the vertical axis of symmetry of the emblem should be parallel to the flyaway of the collar. How to place awards on the police jacket? On the left side of the chest, the awards are arranged in the following order: Badges of special distinction are placed so that the upper edge of the medal block is at the level of the ledge of the lapel of the tunic and jacket. When wearing two or more insignia of special distinction, they are arranged separately in one row, from right to left with intervals of 10 mm between the lateral ends of the stars in the order listed. Badges of special distinction of the same name are arranged in the order in which they are awarded. Signs of orders, orders and medals are arranged horizontally in a row from the center of the chest to the edge, from top to bottom in the order listed. When wearing two or more orders or medals, their blocks are connected in a row on a common bar. Orders and medals that do not fit in one row are transferred to the second and subsequent rows located below the first, placing them also from the center of the chest to the edge in the above order. Blocks of orders and medals of the second row should go under the orders and medals of the first row, while the upper edge of the blocks of the lower row is placed 35 mm below the block of the first row. Subsequent rows are arranged in the same order. Signs of orders, orders and medals are located on the single-breasted police tunic so that the upper edge of the block of orders and medals of the first row is 90 mm below the level of the lapel ledge. On the right side of the chest, the awards are arranged in the following order: Orders are arranged from left to right in the order listed. The upper edge of the largest order of the first row is located at the level established for the common bar (block) of the first row of orders and medals placed on the left side of the chest. Orders that do not fit in one row are transferred to the second and subsequent rows located below the first, placing them also from the center of the chest to the edge in the indicated order. The centers of the orders in a row must be at the same level. The distance between orders and rows of orders is 10 mm. The sign of the number of wounds made of gold-colored galloon (in case of a severe wound) or dark red color (in case of a slight wound) is located on a bar made of the fabric of the top of the item. Galun width 6 mm, length 43 mm. The bad wound badge is placed below the light wound badge. The distance between the stripes is 3 mm. The sign of the number of wounds is placed on the tunic and jacket to the right of the sign to the honorary titles of the Russian Federation, and in its absence, in its place.

Jacket with combined (stitched and removable) insulated lining, removable insulated hood, removable faux fur collar. The jacket is shortened, straight cut. The central fastener on a two-lock detachable "lightning", closed with a wind-shelter valve on the buttons. Turn-down collar with a fastener-paty on a textile fastener. In the area of ​​the shoulder seams there are epaulettes epaulettes View all products by tag epaulettes on buttons with removable false straps for attaching insignia. Shelves and back with coquettes. Along the coquette line there is a red piping. Two breast pockets with flaps on buttons and Velcro fasteners. Two side pockets with flaps on buttons and Velcro fasteners. On the burlap of patch pockets welt pockets with an entrance to the "lightning". On the bottom of the jacket jacket View all products by tag jacket cut-off belt, the volume of which is regulated by the side sections with elastic band stitched on a multi-needle special. chain stitch machine. Sleeves are set-in, two-sutural. On the right sleeve welt pocket with a zipper. A bandage with a reflective tape is sewn inside the pocket, fastened with a Velcro textile fastener. At the bottom of the sleeves there are stitched cuffs with elastic band stitched on a multi-needle special. chain stitch machine. Stitched insulated lining with insulation "Fibertec-200" On the inside of the left shelf there is a pocket for a pistol (with a carabiner on a cord for fastening a pistol) and a patch pocket with a vertical entrance with a zipper. The removable warmed hood is fastened on a detachable "zipper". The volume is regulated by the back of the head and the front neckline. The chin part is fastened with a Velcro textile fastener. Detachable faux fur collar containing Kanekaron fiber (Made in Japan) is fastened with a detachable zipper. Removable insulated lining (vest) made of Firetec 150 insulation, quilted on both sides with lining fabric, fastened with a detachable zipper. On the removable insulation there is a patch pocket with a horizontal entrance with a zipper. Fibertek insulation has a number of advantages over traditional fillers: - Perfectly retains its shape and restores it after washing. - Can be washed and dried multiple times. - Provides greater heat shielding effect compared to other materials of similar thickness and density. - Moisture resistant. - Resistant to long-term use. - It is environmentally friendly and non-toxic insulation. - Practical in terms of price and quality.

Thanks to innovative technologies and quality materials that provide maximum protection against rain and wind, you will be in constant comfort, helping to reduce fatigue throughout the day. Characteristics Protection from rain and wind Statutory cut Upper material: Rip-stop Insulation: Thinsulate

Material: Wool -30% PAN (polyacrylonitrile) -70%

Straight silhouette, length to the middle of the thigh Hood with a detachable edging, adjustable in volume and oval of the face Insulated with two layers of synthetic winterizer, which is 270 g/m or washable) Front zipper with two locks, unzips both from the top and bottom of the jacket Windproof inner and outer flaps covering the front "lightning"; edging on the hood; high collar and bottom of the sleeves, adjustable in size with Velcro with an internal knitted cuff, prevent the penetration of cold under clothing two inside pockets four pockets at the bottom of the jacket Drawstrings: along the waist and bottom of the jacket Material: 100% Polyamide with PU coating Product weight: 46/176 size -1140 g 50/176 size -1207 g 54/182 size - 1302 g 58/188 size -1430 g Designed as a combat jacket, which meant serious checks and tests, having survived outbursts of popular worship and periods of cooling, it returned to us calm and confident in its reliability, functionality and durability. Warm, durable, windproof and water repellent, thanks to the fabric used in the manufacture (100% polyamide with PU coating), "Alaska" provides complete protection from snow, wind, moisture and cold. Insulation - two layers of synthetic fiber synthetic winterizer (270 g / m 2), which, unlike down, does not absorb moisture and is not afraid of frequent washing. The polyester lining is quilted along with it, which increases the life of the jacket (the padding polyester stays in place when dry-cleaning or washing). Unlike expensive membrane fabrics and down insulation, these materials do not require special personal care and do not raise the price of the jacket to exorbitant heights. The hood, characteristic of Alaska, with fur trim, in combination with a high collar, covers almost the entire face, if necessary, and is adjustable in volume and oval of the face. The edge, made of natural or artificial fur (of your choice), can be unfastened from the hood. The inside of the collar and the edge of the hood that touches the face are lined with soft fleece. Serious barriers to wind and cold are also the windproof outer and inner flaps of the front two-way zipper, the belt and the bottom of the jacket that are pulled down with a cord. Sleeves with internal knitted cuffs are regulated by armor on "flypaper". The length of the jacket (to the middle of the thigh) allows you to stay in the cold for a long time, and the free silhouette does not restrict movement. Large buttons allow you to unbutton the jacket without taking off your gloves. The voluminous, warm front pockets are trimmed inside with soft jersey fabric, and the large buttons on the upper pockets allow you to unbutton them with gloves. In addition to the six front pockets, there are two more pockets on the sleeve and two inside. Warm comfortable jacket designed for long stays in the cold.

Worsted wool blend fabric, certified and tested many times, will make your stay in the service comfortable and presentable. CHARACTERISTICS Statutory cut MATERIALS Wool mixture

The boots are made of modern EVA material. They have a high degree of thermal insulation - they keep warm in frosts down to -60 C, they protect against moisture penetration, They are 40% lighter than PVC analogues - the weight of the 1st pair is 700 gr. They provide impeccable walking comfort. Are completed with 2 sl. insulators made of foiled non-woven pile fabric and artificial fur with the addition of natural wool, an extension made of dense water-repellent Oxford fabric. The scope is quite wide: from footwear for winter fishing and hunting to work footwear not associated with aggressive environments. Boots height 40cm. Gender: male Season: winter Material: ethylene vinyl acetate (EVA) Lining detail material: stocking - “thermal felt”, natural wool frost resistance -60С Type of footwear: EVA boots Size table cm 22.5 23 23.5 24.5 25 25.5 26.5 27 27.5 28.5 29 29.5 30.5 31 Russian size (RUS) 35 36 37 38 39 40 41 42 43 44 45 46 47 48 EUR 36 37 38 39 40 41 42 43 44 45 46 47 48 49 UK 3.5 4 195 6.8 7.5 12 13 13.5 Sizing Determine your size as follows: Place your foot on a blank piece of paper. Mark the extreme borders of the foot. Measure the distance between the outermost points of the foot. Find the appropriate size in the table above.

Monochromatic jackets are recommended as a set for the summer uniform "Guard" M4, M5 or M12 in the off-season Elastic knitted p / w elastic band on the cuffs and waist for comfort Metal frontal "zipper" with an internal windproof valve The site presents a camouflage version of this jacket, which allows the use of false epaulettes Pockets: 2 capacious external pockets and 1 internal 1 with a zipper with a section for a fountain pen on the left sleeve Material: Twill (Twill) -100% polyester with PU coating Insulation: Sintepon 150 g/m 2 Product weight: 44-46/170-176 size -611 g 48-50/170-176 size -721 g 52-54/182-188 size -741 g from a glider soaring in the sky - you will not pass by this model. Flight jackets, which were supposed to combine functionality with simplicity, are reflected in this lightweight and practical urban jacket. The shortened demi-season jacket "Navigator" does not hinder movements and is convenient for a bicycle, scooter or motorcycle. The Navigator differs from the "Pilot" jacket only by the presence of a false collar. Thanks to the durable, water-repellent, wrinkle-resistant material (Twill (100% polyester with PU coating)) and synthetic insulation padding polyester (150 g/m 2), of which the jacket is made, the "Shturman" easily resists bad weather, is quickly cleaned and retains its original appearance for a long time. Elastic ribbing at the cuffs and waist provides soft yet secure wind protection. The powerful metal front zipper with internal wind flap inspires confidence. Volumetric side pockets will allow you to place everything you need and will not let your hands freeze, and for the absolute safety of valuable items, the jacket is complemented by two inner pockets and a pocket on the sleeve. Monochromatic jackets are recommended in the set for the summer uniform "Guard" in the off-season. On the camouflage version, you can use false epaulettes. We strongly recommend using front loading washing machines, but if you have a top loading washing machine, it is recommended to wash your clothes and equipment in a special mesh laundry bag to protect against possible damage from parts of the washing machine drum. Close all zippers and velcro fasteners and fully loosen all adjustments before washing. If the upper fabric is membrane, then it is better to wash the product with the lining out (turned inside out). Wash on a delicate cycle at 30°C with a double rinse cycle (it is better to use two rinse cycles to ensure that all detergent residues are removed from the fabric and insulation) and spin at medium speed. It is acceptable to use a tumble dryer at medium temperature (40-60°C) for 30-40 minutes or until completely dry, if the top fabric is membrane, it is better to dry the product with the lining out (turned inside out). You can dry the product in a suspended state with the lining out. For stubborn stains, before washing, treat stains with a special product such as Grangers Performance Wash or Nikwax Tech Wash, allowing the detergent to soak in for 10-15 minutes. It is better to store clothes and equipment with synthetic insulation in a straightened (not compressed) state. How to restore the DWR treatment on insulated clothing or equipment DWR is a special polymer applied to the surface of the fabric to make it water-repellent. DWR processing is not forever. During the operation of the product, as well as after a certain number of washes, the effectiveness of DWR decreases. If water droplets have stopped rolling off the surface of the fabric and wet the fabric even after washing, it's time to restore the splash-proof treatment. We recommend the use of specific fabric re-spray formulations, either sprayed or poured into the washing machine, such as Grangers Clothing Repel or Performance Repel, or Nikwax TX.Direct Wash-In or Spray-On. First wash the product according to the washing instructions, then use the selected composition to restore the splash protection by spraying it directly on the front of the product while it is still damp, or running a second wash cycle, first pouring the required amount of wash-in into the washing machine . The manufacturer's instructions for the restoration of the splashproof treatment on the packaging must be followed exactly. Many DWR reconditioning products require heat activation, so it is best to dry treated clothing and equipment in a tumble dryer or dryer at medium temperature (40-60°C) for 40-50 minutes or until completely dry.

Adjustable straps to fit your height Two-way front zipper that opens at both the top and bottom Additional front zipper lockout to keep it from opening unintentionally Loops for a wide waist belt Adjustable waistband with an elastic band Reinforced knee pads Pleats at the knees for added freedom movement Loops at the bottom of the trousers prevent them from crawling up Side zip vents for easy slipping on of shoes Pockets: 2 side pockets 2 hip pockets Material: Oxford (Oxford) -100% nylon with PU coating "Tourist" -100% polyacrylic with polyamide coating Insulation: Sintepon 150 g/m 2 SIZE SELECTION: Download

With Tuam, frost is not terrible, as there is a warm flannel lining, a warm zipper and a warm collar. The detachable zipper and the ability to zip together the left and right versions of sleeping bags have expanded its application. In a dream, nothing will hinder movement, since the width of the sleeping bag is very comfortable, 90 cm. This will allow you to sleep well. The main thing is not to forget the documents in his pocket. The large dimensions of Tuam do not frighten, since it comes with a compression bag. Certificate number-- Weight, kg-2.04 Type of certificate-Exemption letter Type of packaging-Compression bag Gender-Unisex Certificate expiration date-27.02.2019 00:00:00 Insulation material-Hollofiber GTD number-10702070/030717/0006055/2 Seasonality- All-weather Sostegivanie among themselves-There is a Country-China Extreme temperature-18 Outer fabric -Polyester Lining fabric-Flannel Product category-Sleeping bags Trademark-Greenell Width at the shoulders, m-0.9 Weight pcs. Gross, kg-2.367 Weight pcs. Net, kg-2.04 Unit height. in packing, m-0.62 Length unit. in packing, m-0.45 Unit of measurement of transport packing-box Volume upak. single, cube m.-0.019 Color-Green Main base color-Green

Straight silhouette, length to the middle of the thigh Hood with a detachable edging, adjustable in volume and oval of the face Insulated with two layers of synthetic winterizer, which is 270 g/m or washable) Front zipper with two locks, unzips both from the top and bottom of the jacket Windproof inner and outer flaps covering the front "lightning"; edging on the hood; high collar and bottom of the sleeves, adjustable in size with Velcro with an internal knitted cuff, prevent the penetration of cold under clothing two inside pockets four pockets at the bottom of the jacket Drawstrings: along the waist and bottom of the jacket Material: 100% Polyamide with PU coating Product weight: 46/176 size -1140 g 50/176 size -1207 g 54/182 size - 1302 g 58/188 size -1430 g Designed as a combat jacket, which meant serious checks and tests, having survived outbursts of popular worship and periods of cooling, it returned to us calm and confident in its reliability, functionality and durability. Warm, durable, windproof and water repellent, thanks to the fabric used in the manufacture (100% polyamide with PU coating), "Alaska" provides complete protection from snow, wind, moisture and cold. Insulation - two layers of synthetic fiber synthetic winterizer (270 g / m 2), which, unlike down, does not absorb moisture and is not afraid of frequent washing. The polyester lining is quilted along with it, which increases the life of the jacket (the padding polyester stays in place when dry-cleaning or washing). Unlike expensive membrane fabrics and down insulation, these materials do not require special personal care and do not raise the price of the jacket to exorbitant heights. The hood, characteristic of Alaska, with fur trim, in combination with a high collar, covers almost the entire face, if necessary, and is adjustable in volume and oval of the face. The edge, made of natural or artificial fur (of your choice), can be unfastened from the hood. The inside of the collar and the edge of the hood that touches the face are lined with soft fleece. Serious barriers to wind and cold are also the windproof outer and inner flaps of the front two-way zipper, the belt and the bottom of the jacket that are pulled down with a cord. Sleeves with internal knitted cuffs are regulated by armor on "flypaper". The length of the jacket (to the middle of the thigh) allows you to stay in the cold for a long time, and the free silhouette does not restrict movement. Large buttons allow you to unbutton the jacket without taking off your gloves. The voluminous, warm front pockets are trimmed inside with soft jersey fabric, and the large buttons on the upper pockets allow you to unbutton them with gloves. In addition to the six front pockets, there are two more pockets on the sleeve and two inside. Warm comfortable jacket designed for long stays in the cold. We strongly recommend using front loading washing machines, but if you have a top loading washing machine, it is recommended to wash your clothes and equipment in a special mesh laundry bag to protect against possible damage from parts of the washing machine drum. Close all zippers and velcro fasteners and fully loosen all adjustments before washing. If the upper fabric is membrane, then it is better to wash the product with the lining out (turned inside out). Wash on a delicate cycle at 30°C with a double rinse cycle (it is better to use two rinse cycles to ensure that all detergent residues are removed from the fabric and insulation) and spin at medium speed. It is acceptable to use a tumble dryer at medium temperature (40-60°C) for 30-40 minutes or until completely dry, if the top fabric is membrane, it is better to dry the product with the lining out (turned inside out). You can dry the product in a suspended state with the lining out. For stubborn stains, before washing, treat stains with a special product such as Grangers Performance Wash or Nikwax Tech Wash, allowing the detergent to soak in for 10-15 minutes. It is better to store clothes and equipment with synthetic insulation in a straightened (not compressed) state. How to restore the DWR treatment on insulated clothing or equipment DWR is a special polymer applied to the surface of the fabric to make it water-repellent. DWR processing is not forever. During the operation of the product, as well as after a certain number of washes, the effectiveness of DWR decreases. If water droplets have stopped rolling off the surface of the fabric and wet the fabric even after washing, it's time to restore the splash-proof treatment. We recommend the use of specialized fabric re-splash treatments, sprayed or poured into the washing machine, such as Grangers Clothing Repel or Performance Repel, or Nikwax TX. Direct Wash-In or Spray-On. First wash the product according to the washing instructions, then use the selected composition to restore the splash protection by spraying it directly on the front of the product while it is still damp, or running a second wash cycle, first pouring the required amount of wash-in into the washing machine . The manufacturer's instructions for the restoration of the splashproof treatment on the packaging must be followed exactly. Many DWR reconditioning products require heat activation, so it is best to dry treated clothing and equipment in a tumble dryer or dryer at medium temperature (40-60°C) for 40-50 minutes or until completely dry.

Classic warm women's down short coat for the city. Durable fabric-blend upper with DWR water-repellent treatment keeps out wind and snow, and is smudge-resistant The optimal balance of style, comfort and reliable frost protection, weight, durability and wear resistance of this model make it an obvious choice as a practical everyday urban outerwear for cold weather of the year. Semi-fitted cut allows you to look feminine and at the same time provides more than the necessary freedom of movement Four-layer construction (separate down package) eliminates the migration of down Length to the middle of the thigh Comfortable stitched warm hood with height and front adjustments Removable trim made of natural fur Warm high collar Central two-lock notched zipper Padded internal security placket Padded external placket with press studs Sleeves with warm inner cuffs Articulated elbow fit Pockets: Two padded side pockets with snap button flaps, soft velor burlap One internal zipped chest pocket Material: Outer fabric: 84% polyester, 16 % cotton, 191 g/m2 Lining: 100% nylon 20D 36 g/m2 Insulation: Quality goose down FP600 Down weight: 44/158-164-181.4 g 50/158-164-221.0 g 54/ 164-170-246.1 g SIZE FINDING: Download Down production

Attention! The price of the jacket is indicated without the cost of the edge. You can order the trim separately. A warm yet lightweight Alaskan down jacket for harsh winters. Features loose fit, not restricting movements membrane fabric of the upper with wind and moisture protection and "breathing" properties detachable trim made of natural fur convenient hood adjustment system (top valve, occipital and facial ties made of elastic cord with clamps) shoulder pads made of synthetic insulation high warm collar trimmed with Polartec ® profiled sleeves central two-way zipper protected by an insulating placket, duplicated by two flaps on Velcro ® tape along the placket prevents fabric from getting into the zipper special placket protects the face from contact with the top edge of the zipper six external convenient pockets under the outer placket and on the right sleeve secret pockets with zippers four inner pockets warm Polartec® mitt cuffs with thumb holes windproof skirt waist tie with elastic drawstring with locks Specifications Outer fabric: Nylon Supplex Inner fabric: Advance® Classic Insulation: goose down Weight, g.: 1960 Insulation weight, g.: 470 Insulation type: natural Temperature range, C°: -30 Seam technology: simple Number of internal pockets, pcs.: 4 Number of external pockets, pcs.: 6 Windproof skirt Zipper type : two-lock Hood: non-removable Water resistance, mm. water column: 3000 Vapor permeability, gr.m.kv / 24 hours: 3000 Membrane: Nylon Supplex ® Volumetric cut of the elbow zone Fill Power indicator (for down products): 670

All-weather jacket for police officers. The jacket is elongated, straight cut with a combined (stitched and removable) insulated lining, a removable insulated hood, a detachable faux fur collar. buttons with removable false shoulder straps for attaching insignia. In the area of ​​the shoulder girdle of the yoke, along the line of the yoke, a red edging is sewn in. Two breast patch pockets with flaps on buttons and Velcro textile fasteners. On the vertical side of the pocket there is a pleat for volume. On the bottom of the side seams there are slits fastening with a zipper. The back with a yoke, along the line of the yoke, a red edging is sewn in. Two-seam set-in sleeves. On the right sleeve there is a patch pocket with a vertical zipper entry. A bandage with a reflective tape is sewn inside the pocket, fastened with a Velcro textile fastener. On the left shelf under the windproof valve there is an inner pocket for a pistol with a vertical entrance on a textile fastener. A cord with a carabiner for attaching a pistol is sewn inside the pocket. A stitched insulated lining with a Firetech-200 insulation. On the left shelf on the lining there is a chest patch pocket with a vertical entrance with a zipper. On the right and left shelves there are patch pockets with a horizontal entrance with a zipper. Along the waist line on the lining there is a drawstring with elastic perforated tape to adjust the volume. The free end of the braid is fastened with a button. The removable insulated hood lined with fleece is fastened with a detachable zipper. The volume of the hood in the back of the head is regulated by a patch on a textile fastener. The volume on the front neckline is regulated by a cord with clamps. The chin part of the hood is fastened with a Velcro textile fastener. A detachable faux fur collar with Kanekaron fiber made in Japan is fastened with a detachable zipper and loops and buttons on the collar. The collar is fastened with a shackle with a textile clasp. A removable insulating lining with sleeves with knitted cuffs - wristlets is fastened to a detachable "zipper" loops and buttons along the shoulder seams and the bottom of the sleeves. On the right shelf there is a side patch pocket with a horizontal zipper entry. On the bottom there is a drawstring with a cord for adjusting the volume, at the ends of the cord there are clamps and tips. FIBERTEK INSULATION - Perfectly retains its shape and restores it after washing. - Can be washed and dried multiple times. - Provides greater heat shielding effect compared to other materials of similar thickness and density. - Moisture resistant. - Resistant to long-term use.

Monochromatic jackets are recommended as a set for the summer uniform "Guard" M4, M5 or M12 in the off-season. Pockets: 2 capacious external pockets and 2 internal 1 with a zipper with a section for a fountain pen on the left sleeve Material: Twill (Twill) -100% polyester with PU coating Insulation: Sintepon 150 g/m 2 Product weight: 44-46/170-176 size -631 g 48-50/170-176 size -662 g 52-54/182-188 size -689 g from a glider soaring in the sky - you will not pass by this model. Flight jackets, which were supposed to combine functionality with simplicity, are reflected in this lightweight and practical urban jacket. The shortened demi-season jacket "Pilot" does not hinder movements and is convenient for a bicycle, scooter or motorcycle. Thanks to the durable, water-repellent, wrinkle-resistant material (Twill (100% polyester with PU coating)) and synthetic insulation padding polyester (150 g/m 2), of which the jacket is made, the Pilot easily resists bad weather, is quickly cleaned and retains its original appearance for a long time. Elastic ribbing at the collar, cuffs and waist provides soft yet secure wind protection. The powerful metal front zipper with internal wind flap makes a statement of reliability. Volumetric side pockets will allow you to place everything you need and will not let your hands freeze, and for the safety of small items, the jacket is supplemented with two inner pockets and a pocket on the sleeve. Monochromatic jackets are recommended in the set for the summer uniform "Guard" in the off-season. On the camouflage version, you can use false epaulettes. We strongly recommend using front loading washing machines, but if you have a top loading washing machine, it is recommended to wash your clothes and equipment in a special mesh laundry bag to protect against possible damage from parts of the washing machine drum. Close all zippers and velcro fasteners and fully loosen all adjustments before washing. If the upper fabric is membrane, then it is better to wash the product with the lining out (turned inside out). Wash on a delicate cycle at 30°C with a double rinse cycle (it is better to use two rinse cycles to ensure that all detergent residues are removed from the fabric and insulation) and spin at medium speed. It is acceptable to use a tumble dryer at medium temperature (40-60°C) for 30-40 minutes or until completely dry, if the top fabric is membrane, it is better to dry the product with the lining out (turned inside out). You can dry the product in a suspended state with the lining out. For stubborn stains, before washing, treat stains with a special product such as Grangers Performance Wash or Nikwax Tech Wash, allowing the detergent to soak in for 10-15 minutes. It is better to store clothes and equipment with synthetic insulation in a straightened (not compressed) state. How to restore the DWR treatment on insulated clothing or equipment DWR is a special polymer applied to the surface of the fabric to make it water-repellent. DWR processing is not forever. During the operation of the product, as well as after a certain number of washes, the effectiveness of DWR decreases. If water droplets have stopped rolling off the surface of the fabric and wet the fabric even after washing, it's time to restore the splash-proof treatment. We recommend the use of specific fabric re-spray formulations, either sprayed or poured into the washing machine, such as Grangers Clothing Repel or Performance Repel, or Nikwax TX.Direct Wash-In or Spray-On. First wash the product according to the washing instructions, then use the selected composition to restore the splash protection by spraying it directly on the front of the product while it is still damp, or running a second wash cycle, first pouring the required amount of wash-in into the washing machine . The manufacturer's instructions for the restoration of the splashproof treatment on the packaging must be followed exactly. Many DWR reconditioning products require heat activation, so it is best to dry treated clothing and equipment in a tumble dryer or dryer at medium temperature (40-60°C) for 40-50 minutes or until completely dry.

Fabric - semi-wool. Designed for employees of internal affairs bodies with special police ranks. According to the order of the Ministry of Internal Affairs of Russia No. 575, chevrons chevrons See all products by tag chevrons are sewn on the sleeves of the suit at a distance of 8 cm from the edge of the shoulder. A chevron is sewn on the left sleeve, indicating belonging to the Ministry of Internal Affairs of Russia, and on the right sleeve, a chevron, indicating the service of a police officer. You can add chevrons with Velcro. The jacket is short, straight cut. The central fastener on a detachable "lightning". Turn-down collar. Shelves with detachable yokes in the area of ​​the shoulder girdle. On the shelves there are chest welt pockets with figured buttons on the buttons. Two side welt pockets with zipper entry. Back with stitched yoke. Soft folds are laid along the yoke line for freedom of movement. Single-seam set-in sleeves, with stitched cuffs fastened with buttons. On the bottom of the jacket jacket View all products by tag jacket - one-piece belt, the volume of which is regulated by the side sections with elastic band. A back and a shelf on a lining from a knitted cloth (grid). The armholes are edged with edging tape Trousers of a straight cut. Stitched belt with six belt loops. The volume of the belt is regulated by the side sections with elastic band. Two pockets in the side seams. One welt pocket with a flap and an internal button closure is located on the right rear half of the trousers. A red piping is inserted along the side seams of the trousers. It is part of the uniform of a police officer of a new sample.

The suit consists of a cropped jacket and semi-overalls. The upper part of the jacket is made of fluorescent fabric in yellow color, which will ensure recognition of the employee in bad weather conditions. On the left front part there is a chest patch pocket with a figured flap, fastened with a button and textile fasteners. On the pocket there is a patch with eyelets for attaching a badge. On the right front part there is a pocket for a walkie-talkie. Side patch pockets with shaped flaps fastened with a button and textile fasteners. On patch pockets there are welt pockets fastened with a zipper. On the left front part, under the windproof strip, there is a welt pocket for a pistol. On the front details in the area of ​​the shoulder seam, two loops and loops for attaching detachable shoulder straps are sewn on. A chevron is sewn over the flap of the left breast pocket. On the lining of the left front part, there is an internal patch pocket, fastened with a zipper. Semi-overalls insulated on a lining with a detachable upper part along the waist line from the back side, with three loops, with two chest and two side pockets. Central zip fastening with internal wind flap. On the left front half of the bib there is a patch pocket with a flap fastened with a button, on the right - a welt pocket fastened with a zipper.

Trousers on a belt with loops under a wide belt and shoulder straps regulated on length. Gender: male Season: winter Main color: black Material: "Oxford" (100% polyester), pl. 110 g/m2 Upper material: "Oxford" (100% polyester), pl. 110 g/m2 Insulation material: Sintepon 300 g/m2 Lining material: 100% nylon Normative and technical documentation: GOST R 12.4.236-2011 Special clothing for protection against low temperatures (protection classes 2-4) Country: Russia Size chart Men's size Bust, cm Waist, cm Hips, cm 58 110-118 100-108 112-118 60/62 118-126 108-116 118-124 Male height Height Height of a typical figure, cm Growth interval of a typical figure, cm 1-2 158-164 155.0-166.9 3-4 170- 176 167.0-178.9 5-6 182-188 179.0-191.9 Women's size Bust, cm Waist, cm Hips, cm 40/42 78-86 60-64 86-92 44/46 86-94 68-72 94- Women's 100 48/50 94-102 76-80 102-108 52/54 102-110 84-88 110-116 56/58 110-118 94-100 118-124 Height Height Height of a typical figure, cm Interval of growth of a typical figure, cm

Warm and durable winter jacket. The most popular model. The site presents a camouflage version of this jacket. False epaulettes can be used Quilted polyester lining with padding polyester, which increases the service life of clothes (padding stays in place when dry-cleaning or washing) Frontal zipper with two locks, unzips both at the top and bottom of the jacket Pleats on the back for extra freedom of movement Windproof valve that covers the front zipper, knitted cuffs inside the sleeves prevent the penetration of cold under clothing It is possible to complete the jacket with a hood, collar and liner Stainless buttons are used Pockets: 2 chest pockets and 2 at the bottom of the jacket 1 inner pocket Drawstrings: cord for tightening the belt and the bottom of the jacket Material: Oxford ( Oxford) -100% nylon with PU coating "Tourist" -100% polyacryl with polyamide coating Insulation: Sintepon 300 g/m2