Medicine today 

A vase made of newspaper tubes to decorate a coffee table. How to make a vase from newspaper tubes? For beginners

A floor vase will fit well into any interior, regardless of its style and inhabitants, but here's the bad luck: a good floor vase costs crazy money, and the fragile materials from which it is made are unacceptable in the house with a pet or a small child. How to make inexpensive and unbreakable floor vases with your own hands, our photo master class will tell you.

It is always difficult to make a vase, and even more so an outdoor one, from scratch with your own hands, but a few hours of work spent will save you a considerable amount of money, and the result will delight and make you feel proud of yourself! So, today we make with our own hands a vase woven from a newspaper.

All we need for this workshop is just: a stack of old newspapers, PVA glue, a saucepan lid and a couple of hands.

  • We start weaving with the formation of bundles from newspaper sheets, it is extremely simple to do this: you just need to roll a newspaper sheet into a tube from one corner to another.
  • It is better to cut the bottom of the vase out of cardboard. This technique will greatly reduce your time. However, if you still want to weave the bottom by hand, you should form four bundles of four bundles, and fold them crosswise, alternately each of the bundles should be run in a circle, wrapping each of the four bundles. Thus, the first three rows are woven, and then the quartet of pipes is divided in pairs and three more rows are braided in the same way. Having finished, we already have 6 rows of weaving and now we wrap each of the tubes separately.
  • We turn to weaving the walls of the vase: we bend the protruding bundles up and weave each of them with a bundle. Thus, we form the leg of the vase, its width completely depends on your wishes.
  • Now a lid, or a plate, or in general anything discoid and in area wider than the bottom of the vase, is used. We insert the lid between the posts of the bundles, in the place where the leg of the vase will expand, respectively, the lower you place the lid, the wider your vase will be, and vice versa.
  • We continue to weave 10 more rows using the same technique.
  • Then, with the help of an elastic band, or with our own hands, we begin to gradually bring the edges of the harnesses-racks closer together, that is, we proceed to weaving the narrow neck of the vase.
  • We braid the tapering neck until it is time to braid two strings instead of one.
  • We again spread the harnesses to the sides and weave the border of the vase.
  • We bend one rack after another one by one.
  • Having reached the fifth rack, return to the first one and bend its tail under the fifth rack, and then fix the fourth. Further, according to the same scheme, we bend the second rack along the seventh and cover the sixth, third under the eighth, etc.
  • In the windows that appear in each binding, we skip one rack at a time until a semblance of a braid is formed.
  • Cut off the protruding remains of the tubes and our vase is ready! We cover it with PVA, or transparent varnish and, if desired, paint.

And so we learned how to make a floor vase from the newspaper itself. If you want, using the same technique, you can weave a vase out of twigs, rattan, rubber tubes, fabric, and anything else. DIY vases from a variety of materials are suitable for any home. Such an interior detail can be weaved using different techniques, varied in size, embroidered and painted in absolutely any color. PVA-covered vases are not afraid of moisture, so they are easy to wipe off dust, and the shatterproof materials from which they are made do not injure you and your family.

A master class on weaving a vase from newspaper tubes, step by step with a photo and detailed instructions, will tell you how to make a beautiful vase from a newspaper with your own hands. Such a craft is not only valuable for its originality, but also for the fact that you will do it yourself, to decorate your own home, or as a gift to a dear person. After all, such a souvenir is not a shame to present as a gift on the occasion or just like that.

Weaving the basics from newspaper tubes: a master class

Before you start making MK, you need to prepare the necessary material, namely:

  • jar or bottle;
  • newspaper;
  • glue;
  • paints;

First you need to prepare the newspaper tubes. To do this, cut the sheets of newspaper into 4 parts along the longest length. Now, using a knitting needle, we begin to twist the pieces into a tube. If you place the knitting needle diagonally in relation to the sheet of newspaper, then the tube will turn out to be longer. In this way, make 30-40 tubes and you can proceed to our vase.
First of all, let's figure out how to weave a round bottom from newspaper tubes. We need 3 long tubes, consisting of two regular ones. We put them on the floor in the form of an asterisk.

Now we take two sticks at once and begin to weave them from the middle, alternating their position in relation to the first three.

We build up the tubes as needed. To do this, grease the thin end of one and insert it into the thick end of the other.

We braid our bottom to the desired diameter.

Further, so that our workpiece does not unravel and does not move, you can put a jar of water on it. We fill the ends of our tubes with which we woven the bottom. Further, for work, we need only those that lie at the base. Bend one tube (1) and place it on the next (2). Next, pick up a tube number 2 and put it on the third.

Thus, we braid to the end. The next row of bends of the tubes is done a little further than in the first row. This will create a tilt from the knees of the tubules.

We continue to work without taking out the cans. Thanks to it, your vase will be flat.

If you plan to use a vase for fresh flowers, then you can insert a vessel into it in advance in order to subsequently pour water into it.

We braid our bottle or jar up to the neck, expanding the tubes if necessary. We fill the extra tips inward between the vessel and the weaving.

After the paint is dry, you can walk over it with golden powder or a contrasting color. This will blacken the slanting lines.

Now it remains only to varnish. After the vase is dry, you can use it for its intended purpose.

Very interesting crafts should be recognized and floor vases made of newspaper tubes... It will take quite a long time to make them, but nevertheless, the result will certainly please you.

The first step is to start making the bottom - fold 12 tubes like a snowflake. Remember that the distance and length between them must be the same. There will be 2 working tubes in this workshop. Take one piece, fold it in half and begin to braid the "string" in the already known way, 3 base tubes each. Maintaining a good center position will help you maintain uniformity. Weave 4-5 circular rows.

In the course of weaving, the distance between the base tubes will increase, so braid 2 base tubes each. After going through 3-4 rows, proceed to braiding 1 warp at a time.

Determine the size of the bottom yourself, on average it will take 12 rows. Use a wooden skewer to bend the ends, then cut them off and carefully fix the PVA.

Lift the tubes up under each adjacent one - this will help to make the transition from the bottom to the main form more expressive. As a result, they will all "look" up.

Put some kind of container inside (the shape of your floor vase made of tubes), fasten the ends of the elements with an elastic band, then they will not interfere with your work. If you have chosen a light container, then you also need to secure it with an elastic band to the bottom.

Start weaving with the "string" method - fold one tube in half and start braiding the main ones, you will again get a working pair. The number of rows until the middle of what is being done will be 20. When you reach the middle, the container will need to be removed, otherwise you will not remove it later. Now you need to twist the weaving inward.

The neck can be of any shape. You can use any auxiliary object, for example, a pipe. At the end, bend the tips of the sticks to the outside of the product, this option is more practical. Gently cut off the ends at an oblique angle and secure the PVA.

Floor vase made of tubes - decoration

First of all, you should prime your vase, use a mixture of PVA and water as a primer (just pour a little water into the adhesive and stir). Thoroughly coat the surface with a primer (no bubbles should remain on the surface). Leave to dry for 30-40 minutes.

After the primer is dry, you need to cover the vase with white acrylic paint (if the paint is too thick, you just need to dilute it with a little water). Paint carefully - take a good walk in all hard-to-reach places. After drying, paint with a colorless sauna varnish.

Using the decoupage technique, apply images of lilies to the wicker surface, highlight the drawing with sparkles and paints. If you wish, you can apply the silver polish with a sponge with light movements - you will get beautiful shadows.

The finished vase will look extraordinarily beautiful in the interior. Be sure to make and

Created such beauty Marie s

The secret of the beauty of this work, it seems to me, is in beautiful proportions. In addition, for the first time I see a thing made of newspaper tubes in white. Surprisingly, the vase turned out to be higher than its creator :):

Work process:
You will need 12 metal rods 175 cm long, they will give direction for our weaving.

To create a form, it is necessary to prepare rings of various diameters from polystyrene, for the base you will need gypsum, as well as paper.

Before you get started, paint the tubes in the color you want. Dry it off.

You can dry in an open oven at a minimum temperature, periodically turning it off.

Let's make the bottom for the vase. Glue 12 tubes on a fiberboard circle. Which will serve as the basis for weaving.

Glue a circle of fiberboard of the same diameter on top.

Insert a cylindrical shape of the diameter you need inside, we will braid it.

Fold the guides up and secure. You can fix it with clothespins.

This is how it looks on a vase.

To weave a tall floor vase from paper tubes, you need a strong and stable base.

Cut off the base from the plastic round container, glue it with self-adhesive film.

Divide the base into 12 equal parts. Let's make the marks. For a diameter of 15 cm, you will need 11-12 guides.

Moisten the ends of the metal rods with oil on one side so that they do not rust in the plaster.

Attach the wire to the base with clothespins, for this you will need an assistant. One of you will attach the wire to the base. and the second to hold the entire bundle in the desired position with a ring.

Prepare a mixture of gypsum and water and pour into the base using a paper cornet. Maintain the wire until the plaster hardens. This will take 10-15 minutes.

When the plaster has set, lower the ring inward to press the wire against the edge of the base.

Fill the container with plaster to the end. Allow the plaster to harden well. Dry.

Place rings of different diameters inside the guides to create the shape. Place the largest ring with a diameter of 25 cm at 1/3 of the height of the vase, place the second ring with a diameter of 15 cm at 2/3 of the vase, and the third with a diameter of 17 cm at the full height of the vase.

You can arrange the rings. As you like best - create your own shape.

Now we need a blank, which we began to weave earlier. Carefully lift the prepared form with rods and lower it into the started basket

Let's combine the rods and paper tube guides by gently lifting the wire frame of the vase and turning the woven base.

To prepare the tray, it would be nice to have it rotating on its axis. Having previously laid a napkin on the tray, and putting the napkin under the tray, put the blank on the tray.

After that, you can start weaving the vase. When weaving, turn the tray, so it will be more convenient for you to do the work.

When weaving, insert sheets of thick paper between the wire and the paper guides.

Sheets of heavy paper should be pushed all the way between the wire and the paper guides as you move towards the top of the vase.

Cover the finished vase with varnish. Rings 2 and 3 can be carefully pulled out as you move upward when weaving, to do this, cut or saw them into pieces, and carefully remove between the rods.

The white vase is made using the same technology, only rings of the same diameter were used.

I wish you success!

The article will tell you how to create beautiful things for the home from newspaper tubes.

Weaving from tubes twisted from ordinary newspaper has become very popular recently. Handicraft is quite "budgetary", because a pack of old newspapers can be found in almost every home, and glue and paints are inexpensive purchases.

After studying a few video tutorials and reading the instructions for making wicker products, you can easily start doing this business. Using this weaving, you can create boxes, caskets, vases, figures, trays, dishes and much more.

IMPORTANT: One of the most popular wicker products is a floor vase, which can be used to complement your home interior and use it to store decorative flowers, as well as a planter for a real vase. As a form, you can use any large household items: pots, vases, basins, buckets and much more.

Schemes, patterns, products:

Floor vase: weaving, number of racks
Patterns and patterns for weaving
Wicker floor vases: finished products
Unusual floor vase with flowers (pots)

Video: "Vase from floor tubes"

Weaving a vase high from newspaper tubes: patterns, patterns, description

Weaving a vase:

  • Start braiding in the usual way
  • First, you should make a bottom or take a cardboard base as a basis.
  • Roll and fix the tubes up
  • Weave the tubes, each time lengthening them with a new piece of newspaper and holding it together with glue.
  • You can shape the vase by regularly changing the bases, for example, lids from pots of different diameters (look at the photo).

Step-by-step weaving of a vase
Vase formation The final stage of weaving a vase

IMPORTANT: When forming the edge of the vase, the ends of the tubes are pushed inward and cut off, they can be fixed with glue. The finished product can be opened with acrylic paint and, after drying, covered with a layer of varnish, which will make the product stronger and give a glossy shine.

Video: "Master class of a floor vase"

Spiral weaving of a vase from newspaper tubes: diagrams, descriptions, photos

The spiral weaving is characterized by a beautiful pattern and ease of pattern creation. Any product can be made with such weaving, both a box and a vase. During weaving, you must use the instructions and watch the video of the lesson.

Spiral weaving of a vase with a base-bottom Spiral weaving: photo of the beginning of work
Weaving principle: large folds

Video: "Spiral weaving of a vase"

Weaving flower vases from newspaper tubes: photo

What is important in weaving from newspaper tubes:

  • Have a large supply of material. It often takes many sheets of newspaper to keep the tubes tight.
  • Have a lot of glue. It is desirable, of course, to use dry pencil glue, but it is quickly consumed and costs several times more than ordinary PVA.
  • It is desirable to weave from already dried tubules.
  • Use a knitting needle or crochet hook as you work to help align and adjust the weave.
  • Cover the finished product with a layer of acrylic paint or automotive paint (in a spray can). After the paint layer has dried, it is advisable to open the product with a layer (or maybe two layers) of varnish.

The scheme of weaving a small vase from newspaper tubes

Weaving fruit vases from newspaper tubes: photo

Dishes made of newspaper tubes are perfect for storing non-damp foods, such as baked goods, bread, sweets, sweets, fruits. Tight knitting and opening the product with varnish will help the craft be strong, but at the same time lightweight. After drying from paint and varnish, such fruit bowls and dishes can not deteriorate from an extra drop of moisture.

IMPORTANT: The bottom of fruit bowls, candy bowls and dishes from newspaper tubes must be woven by hand, and not inserted into a cardboard base.


Weaving dishes from newspaper tubes

Finished goods:


Breadbox
Fruit platter Candy bowl

Weaving vases from newspapers: photos of models

Look through photos of ready-made products that were knitted by skilled needlewomen and find your own ideas for creating original interior items, vases, dishes and boxes from newspaper tubes.