Corset lace wedding dress. How to sew a corset with your own hands - from pattern to tailoring. Side lacing

07.04.2019

The clasp of which does not experience large mechanical loads can be made from braid or a decorative cord. Cut 2 pieces about 1.5 times the length of the cut or seam. Set aside 1-2 cm from the edges of both pieces (the distances should be the same). Mark these points. This is the beginning of the first loop. Measure the length of the actual loop. The size of the loops depends on the style and thickness of the cord. For a thin braid, 2 cm will be enough, for a wide one - up to 5 cm. Mark the end of this segment. Further to the end of the cord, set aside the distances between the loops and the segments on the loops themselves.

Align the start and end points of the segment for the first loop. It is better to make holes for lacing with a half-eight, that is, so that one end of the braid goes to the other. If you are lacing with picot braid, you can sew the ends of the loops behind the picot, as in the manufacture Irish lace. In any case, the beginning and end of the loop must be tightly fastened to each other. Make the rest of the loops in the same way. Make sure that the distances between them are the same. Don't forget about symmetry.

Place the prepared braid on the processed section of the product so that the loops are directed in the opposite direction. The braid can be sewn both to the wrong side and to front side. In the first case, only loops protrude beyond the edge of the product. In the second, the braid also plays the role of decoration. Baste it and attach it with a regular or decorative stitch.

Lacing can also be made from a homemade steering wheel. Cut out 2 strips. Their width is 3-4 cm, and is calculated according to the same principle as in the case of braid. Fold the strips in half front side out. Align the long cuts and iron the folds. Fold each half in half lengthwise again. Place the open edges inside the binding and press again. Stitch the seam with a regular or decorative stitch. Loops do exactly the same as in the first method. If the fabric is enough, then it is better to iron the loops at the folds. It is better to sew such lacing to the wrong side or sew it into the seam.

The modern seamstress has much more opportunities than the medieval craftswoman or even the needlewoman of the last century had. Accessories and tools for making laces can be bought at many sewing stores. It can be, for example, eyelets. If you insert them, you get a hole edged with metal or plastic, the same as on boots. There may also be eyelets in the form of buttons, in which the loop is on top. Very often, special tongs are also attached to sets of accessories. Maybe a stapler. Several eyelets are inserted into it, and then they act in the same way as those intended for paper. Mark the location for the hole. Bring the fabric between the planes and clamp the stapler. Manual - also not a curiosity, it is more than once useful for attaching not only laces, but also buttons. The principle of operation of all tools is approximately the same. The eyelet consists of two parts - a cylinder and a washer. If you insert it with tongs or a press, then the wider short part of the cylinder should remain on the front of the product. Having punched through the fabric, bring the long part of the eyelet to wrong side. Place the washer and clamp the entire structure with tongs or a press.

Decided to opt for a wedding dress with a corset? Then you should learn how to properly lace it up. In this article you will find detailed instructions, videos and photos. We have collected many useful tips for brides. They will allow you to lace up the outfit beautifully and without harm to health. You will learn in what order it is best to do this, what to use and under what conditions.

Experts wedding business it is advised to start lacing the dress before the bride puts it on. It is much easier to start threading the ribbons on the corset when the outfit is on the hanger. You need to finish the process directly on the girl's body. This option is especially relevant when it comes to.

First you need to arrange the dress in such a way that it is convenient to work with it. You can hang it on a hanger or put it on your bed. You need to start lacing the corset from top to bottom, without tightening it at the same time and observing a distance of 10 cm from the edges. The tape or cord is threaded into the upper loops. The ends should be aligned in length.

Make sure the tape lies flat. To do this, you need to constantly straighten your hands.

Having reached the waist area, you need to leave a few free loops of 20 cm each. You can lace up to the very bottom. Ribbons are allowed to be tied in a bow. Next, the bride can put on a dress and pull the corset to fit her figure.

How to properly tighten the corset according to the figure of the bride

It is best to put on your attire through your legs. This will not spoil the makeup with the hair. First of all, you need to fasten the zipper, if it is present on the corset.

You can tighten the corset alone, but it is better to get an assistant.

Traditionally this is done by one person who:

With his left hand he holds the ends of the ribbon, and with his right hand he gradually pulls it down and sorts it out in places where crosses have formed. It is important to smooth the tape so that it has an attractive aesthetic appearance.
Once at the waistline, you need to tighten the corset. You can not do this in the chest area, so the bride will not be able to breathe normally. At this point, she should be asked to raise her chest with her arms folded.
Make sure the zipper runs down the center of the back.
Make sure that the dress is tightly fixed on the bride. To do this, ask her to walk around in a dress and find out about her feelings. Then proceed to the formation of the bow. He might be different shapes and pomp. Always in fashion classic version. The length of the ribbons can vary from 5 to 10 cm. To prevent the cord from starting to untie, it can be smeared with colorless varnish.

The elongated corset requires special attention. The procedure for tightening it is almost the same as described above, but has one caveat. Having reached the waist, the tape must be pulled out and a margin of approximately 15-20 cm should be left. Having laced up to the very end, we form the first bow. We tighten the loops left earlier and tie the second bow out of them. We level the tape and enjoy our work.

We suggest watching a video that shows in more detail how to lace up correctly Wedding Dress satin ribbon:

If you are lacing a bride's attire for the first time, it's best to start with the dress taken off.
Lacing is recommended to start at the top and go down.
If there is a zipper, the first thing to do is fasten it, and then proceed to lacing.
The bride's dress should fit snugly around the waist.
During lacing, you need to support the bride's chest with your hands so that she has nice shape.

Pregnancy is not a reason to refuse an outfit with a corset. You need to lace up to the strip along which the bra line runs. At this point, the ribbon is tightened and a bow is formed. Then they continue to lace up, but so that the stomach is not overstretched and the bride feels comfortable.

When it is important to lace up the bride so that no skin folds form over the corset. Ask the girl to stand straight and straighten her shoulders, and only then start lacing. In this case, you can not tighten the tape too much. You also need to make sure that it does not dig into the skin.

Here is another video from detailed instructions for tightening the corset on a wedding dress:

Photos of lacing wedding dresses

We offer a selection of interesting laces:

This is a classic version of corset tightening. It looks beautiful on a straight dress and "mermaid"

Here is another option for the "fish" model

Low back lacing

And this is a wide, but not high lacing, modern way tighten corset

Follow all the instructions exactly, and you will definitely succeed!

In order to emphasize thin waist bride or hide overweight, many young ladies choose a corset. This is quite conscious and right choice. Every corset has a lacing that needs to be tightened.

This must be done in accordance with all the rules so that nothing blooms and does not fall at the celebration. Therefore, the witness or mother must prepare and know in advance how to lace up a wedding dress.

Nuances of lacing

Very important point The thing that all girls should remember is to strictly according to their size.

No matter how surprising it may seem, a lot of young ladies prefer to wear the outfits of their acquaintances and girlfriends, which are either much larger or smaller. Many people think that by tightening the corset, you can get a good look.

In fact, you will only spoil the appearance.

You can only lace on a person. It is not allowed to start work without trying on. Ask the bride to put on a dress and fasten all available locks. Only after this you can start lacing.
If a friend or witness has never done this work, they should practice well so that at the crucial moment they don’t miscalculate, but do really high-quality work.
It is necessary to start the procedure from above and slowly go down. At the same time, the bride should stand straight, straightened up and keep her hands on her waist.
Remember that you can only tighten the waist. In this case, you can get the effect of the so-called wasp waist. If you tighten the top, namely the chest, it will be very difficult to breathe.
If the chest is small, and you want to visually enlarge it, then during work the young lady should cross her arms at the chest line and slightly raise them up.
If there is no lining under the corset, but Open back- it means that it is necessary to do the work so that the lacing lies beautifully on the back, and does not dig into it.
If the bride is pregnant and is on short term, then it is better to refuse this dress, because as a result there may be health problems.

How to lace up a removed dress

Lace up is a responsible and serious occupation. It is especially difficult to make it for those who have never done it. You have to figure out how to do it right. Many lace up so that it turns out very ugly.

To prevent this from happening, there is one simple way - to do everything on the removed dress, then put it on the bride and carefully fit it to the available sizes.

Hang the dress on a hanger, make it at the level of your face. You should be able to see everything clearly.
Thread the laces into the upper holes and start to go down from top to bottom.
At the same time, do not tighten the rope, but leave it free.
Count the middle and leave 2 empty holes on each side.
Having bypassed the holes we need, continue lacing.
Tie a loose bow at the end.
Ask the bride to put on her dress. Look at how the corset sits on her, adjust it by fitting it to the figure. Tighten some lines, loosen some.

This type of lacing is ideal when the wedding dress has an open back. As a rule, in such cases lacing occurs with a satin ribbon or bow. The fabric used is dense and tight-fitting, there is a lock on the side.

Lace option.

The lacing itself is more of a decorative character. The task of the witness is not to harm by passing chest. Otherwise, you don’t have to worry, the dress will remain on the hero of the occasion for the whole day.

How to lace up a worn dress

How to lace up a corset.

It is best to lace in this way after several attempts and training. Therefore, if the bride asked you to do this, let her know in advance that you have never tried it and would like to work out.

Check out simple rules, and in this case, in the future, you can get quite a decent result.

Carefully helping the bride to put on the dress. This is done through the legs. It is worn under the dress.
We fasten all available zippers and buttons. US you need to see a clear silhouette. Now it depends on the girlfriend how the bride will look at the celebration.
The future spouse should stand straight and even, the back should be straightened, and the hands should lie on the hips.
Pass the tape through the top loops and start lacing slowly. The method is carried out from top to bottom. Pay attention after each hole to the length of the tape. And on the one hand, and on the other hand, it should be the same. If this does not happen, it should be tightened more tightly.
It is easier and more efficient to lacing with two people. One friend will hold the edges of the tape, and the second will tighten as needed. In this case, you will get really high-quality work.
When lacing up the chest, the bride should keep it under the corset with crossed arms. This is necessary so that only the waist line is tightened. Otherwise, there is a high risk that even the most beautiful breasts becomes very flat.
At the time of the procedure, look at the fabric, which is a corset. She shouldn't shrink. It should be spread evenly different sides.
If you have finished the work, then once again carefully check whether the corset is really tight, whether you tightened it successfully. Do you have more it is possible to tighten or loosen the lacing.
Tie at the end beautiful bow. Better to do it with big ears. In this case, it will look gentle and airy. Make sure that the bow itself sits firmly so that it does not come loose.

Useful video

How to lace up wedding attire.

How to lace up a corset for a wedding dress.

Dress lacing tips.

Conclusion

Wedding dress with lacing perfectly emphasizes beautiful figure bride. It helps to create gentle and romantic image. Not the last role in this is played by the corset itself. However, you need to think in advance how you will lace up, and who will do it.

One of the options is to order a service in wedding salon. Experienced craftsmen on the appointed day, the bride will be fully dressed, making the lacing on the wedding dress flawless.

Hello, Dear friends. Not so long ago I published an article about wedding dresses with a corset. Reviews and comments have shown that not all girls know how to lace up a corset on a wedding dress correctly. That is why I decided to devote a separate article to this issue.

After reading it to the end, you will also learn about what types of corsets exist, why these models are most often chosen. modern brides why the corset can fall down. Stay with me and all your questions will not go unanswered.

Corset Benefits

This amazing piece of women's wardrobe can transform you in minutes. Most often, of course, the corset is used in wedding dresses. Almost all collections of 2017-2018 contain such. It can be combined with puffy skirts, short or elongated bottoms, which opens up a lot of possibilities for your imagination.

It is thanks to the corset that you:

look feminine and graceful;
you can hide flaws;
emphasize the waist and chest line.

What dresses to choose

A properly selected dress will hide flaws and emphasize the dignity of the figure, create a beautiful silhouette and impeccable posture.

A good choice would be, that is, a standard or elongated corset in combination with a very fluffy skirt from organza or tulle. If there are imperfections on the legs or hips, the skirt will easily hide them from prying eyes.

The lowered bodice harmonizes very beautifully with a mermaid or fish style dress. But such a toilet is not suitable for everyone. It is worth buying for owners narrow waist And tall. A very similar option is a year-style dress.

Lace options with a thick satin ribbon look delicate and elegant. Depending on the type of cup, they are able to visually enlarge the breast or, conversely, support it.

Transparent models look great. They are not vulgar, they immediately attract attention and are suitable for brave brides. good decision will be decoration with embroidery, stones, rhinestones or pearls.

How to lace up

I found out that not all girls know how to properly lace up a corset on a wedding dress. Today, several types of lacing are used in this type of bodices.

Holes through which a thin cord is threaded (fabric may be present to adjust the size).
Wide ribbon loops.
Narrow cord loops with zipper.

Lacing pattern

In fact, there is nothing complicated. Proper lacing is a guarantee that the bride's outfit will fit perfectly on the figure. I must say right away that you won’t be able to do it yourself, you without fail need an assistant. Practice before the wedding so that on the day of the celebration you do not waste time on this.

If you don’t know how to lace up a corset for, then try to do everything according to the technology that I offer you. If everything works out, you will feel comfortable.

Write in the comments how helpful the tips were.

Lacing rules

Knowledge of the principles of lacing is a pledge good mood bride.
Lacing is done only on the bride. If there is a zipper, then it is fastened first. Only after that a ribbon or cord is threaded. The direction of lacing is from top to bottom, not otherwise.
When lacing crosswise, you need to look so that the ends of the tape are identical. The cord itself is not tightened too much, you need to adjust after. It is important that the tape is not twisted.
Next, a tightening is performed: the ends of the tape are held together, in the places of its intersection, a tightening is carried out. Repeat the procedure several times. The tightening is done until the corset fits snugly around the camp.
While tightening the corset, the bride should hold the bodice, and not keep her hands on the waist. This is necessary so that the chest is not tightened too much.
In the chest area, the bodice is slightly released, but in the waist, on the contrary, it is tightened. This will provide comfort and a beautiful silhouette.
Excess material is carefully tucked under the bones in different directions. The clasp itself should be exactly in the center.

Below you can clearly see the diagram.
When the dress can fall
There were situations in my life when the bride had an incident with a dress at a wedding. If you chose an outfit with a corset, it can only fall off because of the corset itself. There can only be two reasons:
the dress is too big for you;
very loosely laced corset.

A simple experiment will help you understand if the dress fits: just put on the outfit, and then try to stick your finger between the lacing and open back. If you succeed, the dress needs to be sutured. To prevent the lacing from unraveling, it is necessary to lace up from the top down, and not from the bottom up.
I am sure that after all that you have seen and read, you understand how to deal with a corset. All that remains is to choose the right accessories, make beautiful make-up with a hairstyle, put on a veil and, take it in hand, and you are 100% ready.
Rest assured, the brides of such large cities as Moscow and St. Petersburg do not choose outfits with a corset for nothing, because they will be popular even in 2019. Just look at the photo. How different and beautiful design solutions, what exquisite decor, what images!
And that's all I have. Do not forget to subscribe to updates, share the article in in social networks. Also, take a look at where you can take help and advice from leading experts. I will be glad to see you again. Until we meet again, friends!

At first glance, there are no secrets on how to lace up a wedding dress. Then it turns out that this process has its own peculiarities and nuances, because the lacing can start at the top and end with a bow at the waist, it can start from the bottom (and this is also not easy to deal with), be on top of the zipper and perform an almost decorative purpose.

Habitually lacing up sneakers or boots turns out to be so easy compared to wedding chores that fiddling with weaving ribbons seems like a difficult job. It's just that this process has its own rules.

The rules for lacing a wedding dress are different, depending on whether it is done from top to bottom, to tie a bow, or from bottom to top, when it is necessary to lace up the corset not for decorative purposes, but in order to give the chest a beautiful shape and squeeze the sides a little.

The main requirement is not to squeeze the chest, because the bride will not be able to fully breathe. The remaining conditions must be met so that the corset on the wedding dress sits as well on the figure as possible, without violating the harmony of the bride's appearance. Inaccurately executed rows will spoil the impression and give the appearance of sloppiness and sloppiness.

Incorrectly laced corset weaving will not fulfill its intended purpose: after a while it will disperse, the sides, and the corsage will sag ugly. Sometimes the cause of an inaccurate appearance is an incorrectly selected corset size, or insufficiently close edges.

The minimum distance to which it is necessary to tighten is 3-5 cm, but no more, and if this fails, and even the lightning does not converge, the dress is chosen incorrectly.

Strongly tightened lacing usually digs into the body, especially if the thickness of the laces is small, and the necessary decorative effect disappears from the ribbons, they wrinkle and also begin to cut the skin.

The opposite effect is obtained when it is tightened to the stop, and you can still stick your finger under the weaving - then the bride is forced to constantly worry about the falling corset, and furtively correct it.

This is not the most pleasant thing to do on a significant day, which should only leave Nice memories. The corset is never laced up on its own, for this you need an assistant who has at least a little idea of how this is done. But the bride can make the initial stitches on the dress herself while it is still hanging on the hanger.

After that, the wedding dress will have to be put on through the legs so as not to damage the already finished hairstyle and makeup.

You should always consider the features of the device wedding corset, especially when buying in the hope of future weight loss:

a model with a fabric backing will allow you to slightly increase the size if the corset is frankly small;
thin laces are usually elastic and allow lacing, but they cut hard into the body, and it looks unappetizing;
the most beautiful one is laced with a ribbon, but it must be perfectly sized.

How to tie a corset on a wedding dress taken off - tips

While the dress is not on the bride, you can start lacing it on a hanger. Sometimes it is advised to lay it out on the bed, but this way it can be easily crushed, and the process is not particularly visible.

The lace or ribbon is threaded into the upper or lower extreme loops (depending on what kind of lacing is planned - with a bow that is made with a ribbon and is located at the waist, or coquettishly - just below it) or with an elastic cord, the edges of which are tied into a minimal knot and hidden over the edge.

The loops can be under the knots (and this is the most common way) or on top, hiding the crosshairs. But for the last way requires skill and dexterity, which for some reason are not found in any of those present.

That third of the lacing that is not fixed on the bride should be as tight as possible, so the lace or ribbon is pulled on itself with force before the ends are threaded into the next loop and fixed again in a criss-cross position.

In the photo, such a process rarely looks intelligible, so you can see the picture below.

Instructions for lacing a corset on the bride

The wedding dress begins to take on its final form when it is already on the bride. If the process starts from the waist, it is much easier, because the initial fixation in the waist area (just where the part of the wedding dress should fit as close as possible) has already been done.

When lacing starts at the top, the edge on the back is left relatively loose (it is pulled up at the end, sequentially, from bottom to top to ensure maximum fit, but the closer to the waist, the more the tape or lace is pulled together). The main condition in both the first and second cases: the ends of the lacing means must be absolutely equal in length. With center alignment, any lacing method begins.

To tie a bow of such a size that the author of the model was counting on, the corsage must be selected strictly in size. Even if there is an insert under the lacing that masks the lack of edges, the length of the tape will go extra centimeters, and the bow will be small or primitive.

After a perfect match is achieved between the ends of the lacing device, the ends are threaded into loops with opposite sides, that is, the left one is pushed into the right loop, and the right one into the left loop.

Then the action is repeated in the same sequence (again, the left end into the right loop, the right end into the left loop). As soon as the segment of the necessary rapprochement comes, the intersection of the ends is tightly held with a finger free hand, and it's better if someone else does it.

When the preliminary knot is tied, the lacing is sequentially pulled along the loops in the right direction so that it is not difficult to stick a finger under it.

Here you will see more clearly how to properly lace up the corset of a wedding dress:

This dress looks very elegant. And what dress did you have at the wedding, and how significant were the difficulties if it was laced? Share with us your opinion on this matter.